Siemens IC60 Manual de usuario Pagina 78
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Miscellaneous installer and panel options
78
Building Technologies
Fire Safety & Security Products
14 Miscellaneous installer and panel options
14.1 Miscellaneous panel options
Miscellaneous Options
P25E 10E1-8E
Option Display text Description
1 Tamper uses
EOL
Panel Tamper is 2k2 EOL: the tamper input (TMP) on the control panel requires either
a short circuit or a 2k2 End-of-Line resistor. If option 1 is on the panel must see a 2k2
resistor (EOL) across the TMP & 0V terminals to ensure the tamper is sealed. If this
option is turned off then a simple short circuit is all that is required to seal the panel
tamper.
2 Installer Direct Direct access to program mode for the Installer Code: if this option is on, the Installer
Code can gain access to Installer Program Mode directly. If the option is turned off,
the installer can only gain access to Installer Program Mode via Client Program Mode.
This option allows the owner to control program mode access by the installer. The
User must have option 3 at location P5E turned on for them to allow installer access.
3 Ignore AC Fail Disable Mains Fail Test: if the panel must be run off a DC supply or the Mains supply
can fail regularly, this option disables the mains voltage monitoring to prevent mains
fail alarms from occurring.(e.g. If used on a boat or camper by battery)
4 Output1 Low
Volume
Listen-in to Output # 1 Low Volume: if Listen-In to Output 1 is turned on (P175E 8E),
the level of sound from the speaker can be controlled with this option. If this option is
Off the sound level during listen-in to O/P 1 is high volume, turning this option On
makes the sound level low volume. For listen-in to Output 1 to work the device
connected to O/P 1 must be an 8Ώ speaker and the output must be modulated (P35E
1E Option 1 on). Failure to do this could result in damage to the speaker & output.
5 No Arm RF Fault Receiver Fail Lockout: if the receiver fail delay (P25E 7E) is set to a value other than
0 and the panel sees no activity from the receiver for the set period of time, a receiver
fail alarm will be generated. If this option is turned on, the panel cannot be armed until
the cause of the receiver failure has been resolved.
6 Output data to
bus
Send Output information to Keypad Bus: there is an optional 4 x relay output
expander board that can be connected to the keypad bus if required. For this output
expander to work option 6 must be turned on for the data to be sent on the keypad
bus to the expander.
7 No Arm AC-Low
Battery
Cannot Arm if System battery is Low: if the panel battery is low, normally you can arm
the panel leaving the battery to charge over a period of time. If this option is turned
on, the panel cannot be armed until the battery is either fully charged again, or it has
been replaced (if faulty).
8 Installer Lock Installer Lockout: normally if the panel is powered up with the panel tamper open (e.g.
system tamper alarm active) and in the Disarm state, then the panel will go into
installer program mode when the
P
r
og
then buttons are pressed. If this option is on,
the panel will not allow access to program mode on power-up and the only valid
method of accessing program mode is via the installer code.
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Siemens IC60
Los Sistemas De Control De Acceso De Seguridad Siemens SINUMERIK 802D sl Manual de servicio
(50 paginas)
(50 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens SINUMERIK 802D sl Especificaciones
(392 paginas)
(392 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Especificaciones
(150 paginas)
(150 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Manual de servicio
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens FIREFINDER-XLS Manual de inicio rápido
(72 paginas)
(72 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Manual de usuario
(184 paginas)
(184 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales