Siemens IC60 Manual de usuario Pagina 134
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Telephone numbers
134
Building Technologies
Fire Safety & Security Products
Phone D Reporting
P189E 1-8E 1-8E
Option Display text Description
1
Latch Key Report
Report Latchkey Disarm: if the panel is armed in Latchkey Report Mode by using a
Code, Key-switch,
, , or buttons, any code or key-switch without the
Latchkey option (P4E or P122E Option 6 off) used to disarm the Alarm will cause a
Disarm report to be sent via the dialer. Normally the report format for the telephone
number would be set to Domestic or Voice reporting.
2
Delinquent
Report
Report Delinquency Alarm: if the panel has been configured for Delinquency
monitoring (P67E) and an area has not been armed for the time set at P67E, a
Delinquency Alarm will be sent to the Monitoring Station if Contact ID or 4 + 2 is set
as the reporting format.
3
Tests Report
Send Test Calls: if Contact ID or 4 + 2 formats are used for reporting alarm, the panel
can also send Automatic test calls. If this option is turned on the test calls will be sent
but if test calls are not required they can be disabled by turning this option off.
4
Fuse Report
Report Fuse Failure: the panel has two on-board thermal fuses designed to protect
the 12 V DC outputs from short circuits. If this option is on and either of these fuses
are open, a report will be sent to the monitoring station if Contact ID is set as the
reporting format.
5
Output Fail
Report
Report Output 1 or 2 Fail: the panel has two high current outputs (output 1 & 2).
These outputs are normally used to drive sirens or strobes for local alarm warning. If
option 8 at location P37E is on for either output 1 or 2 the output status will be
monitored (e.g. wire to siren has been cut). If this option is on and a fault is detected
on the output, a report will be sent to the monitoring station if Contact ID is set as the
reporting format.
6
Time Change
Report
Time Change Reporting: if this option is turned on all changes in the RTC – real time
clock setting will be reported.
7
Missing Keypad
Report
Missing Keypad Reporting: if this option is turned on and a Keypad is disconnected it
will be reported immediately.
8
RF Blocking
Report
RF interference (Jamming) detection: if the System detects a RF signal which is not
according to the transmission standard of EN 50131 a jamming signal (frequency
blocking) will be reported.
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Siemens IC60
Los Sistemas De Control De Acceso De Seguridad Siemens SINUMERIK 802D sl Manual de servicio
(50 paginas)
(50 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens SINUMERIK 802D sl Especificaciones
(392 paginas)
(392 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Especificaciones
(150 paginas)
(150 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Manual de servicio
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens FIREFINDER-XLS Manual de inicio rápido
(72 paginas)
(72 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Manual de usuario
(184 paginas)
(184 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales