Siemens IC60 Manual de usuario Pagina 44
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LCD keypad
44
Building Technologies
Fire Safety & Security Products
8.2.1 LCD keypad Installation
Bus connection
The connection to the Sintony 60 control panel is realized over the system bus. It is
an intelligent member of the Bus with a unique Bus address (refer to Keypad Set
up). It could be installed external to the Sintony 60 Control Panel (modular and
compact version). The terminals are connected with a 4 wire cable to the
corresponding terminals on the Control Panel marked POS, NEG, CLOCK, &
DATA.
The 5
th
bus wire- Listen dialing function
The 5th wire is an optional Listen-dialing connection. It is connected from the LIN
terminal of the keypad to the Lin terminal of the panel keypad port. With the Listen-
in wire connected the user is able to hear the call progress during dialing at the
keypad (only if the program options at address P175E 6E are turned on).
Maximum cable length
The maximum recommended cable using standard 0.6mm security cable is 25m.
Cable runs exceeding this distance may require 0.8mm cable. Always use good
quality cable. Some installations may require CAT5 data cable to ensure data
integrity in noisy sites.
Keypad Tamper Switch
The LCD keypad has a tamper switch at the back side. Make sure that when the
Keypad is installed the Tamper contact is closed by the pressure of the wall. If the
switch needs some adjustment, the tamper contact could be fitted with an
additional distance screw to ensure proper contact to the wall and therefore a good
protection of the housing against manipulation.
Activation- programming - addressing
A LCD Keypad has to be learned to the system. To start after installations with the
first steps please refer to the chapter
8.4: Programming a keypad to the system –
addressing. This contains:
z Change language
z Address the keypad to the system bus
z Copy text files into the new Keypad
8.3 Programming a LCD keypad – Local program mode
The Keypad can be programmed locally via the Keypad buttons or by a PC with
the separate available programming cable IAQ6-1 and the programming Software
Sylcom 60 IAS6-1 through the programming interface port on the back side of the
Keypad. (It could also be programmed remotely through the programming port of
the control panel unit if connected to the bus).
In the local program Mode object related names like Zones, Users, Outputs etc.
can be programmed. System settings have to be programmed in the Installer
Program Mode (see chapter
9.4.1: Access to installer program mode).
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Siemens IC60
Los Sistemas De Control De Acceso De Seguridad Siemens SINUMERIK 802D sl Manual de servicio
(50 paginas)
(50 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens SINUMERIK 802D sl Especificaciones
(392 paginas)
(392 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Especificaciones
(150 paginas)
(150 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Manual de servicio
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens FIREFINDER-XLS Manual de inicio rápido
(72 paginas)
(72 paginas)
Los Sistemas De Control De Acceso De Seguridad Siemens Codelock K44 Duo Manual de usuario
(184 paginas)
(184 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales