Siemens SPCK421 Especificaciones descargar pdf (Pagina 288)

Appendix

Zone attributes

288

Siemens AB

A6V10276959

Security Products

18.11.2011

Analysed

The Analysed Attribute must be set for a zone if that zone is wired with an

inertia sensor. The Pulse count and Gross attack values should be

programmed for each inertia sensor on the system in accordance with the

results of a simple calibration of the device.

Pulse Count

Pulse count trigger level for analysed inertia sensors.

Gross Attack

Gross attack trigger level for analysed inertia sensors

Final Exit

The Final Exit attribute can only be assigned to an Entry/Exit Zone type. Use

this attribute to override the standard process of counting down the exit timer

whenever the system is full set. When all other entry/exit routes in the

premises are closed, fullset the system and close the final exit/entry zone. As

soon as the door is closed the Final Exit time will count down to setting the

system.

Shunt

A zone with the shunt attribute set will be inhibited whenever a shunt type

zone is opened. This provides a mechanism to group the inhibition of zones

with the opening of the shunt zone type.

Report Only

This attribute only applies to the FIRE zone type. If this attribute is set, then

activation of the fire zone will only report the activation to the central station.

No alarms will be generated on site.

Open Only

This attribute only applies to the KEYARM zone type. If set then the setting

state of the building will toggle on openings only.

Fullset Enable

This attribute only applies to the KEYARM zone type. If this attribute is set

then zone activation will Fullset the system/area. Apply this attribute if it is

intended that the user should only have the ability to FULLSET the system

from a keyarm zone.

Unset Enable

This attribute only applies to the KEYARM zone type. If set then zone

activation will Unset the system/area. Apply this attribute if it is intended that

the user should only have the ability to UNSET the system from a keyarm

zone.

Keyarm Fullset

This attribute only applies to the KEYARM zone type. If set then zone

activation will Fullset the system/area.

Keyarm Unset

This attribute only applies to the KEYARM zone type. If set then zone

activation will Unset the system/area.

Tech Zone Report

Allows a zone when opened, regardless of the mode to send an alarm to the

ARC in FF, CID, SIA and SIA extended. When areas are selected, the alarm

will only be sent to the ARC to which the area has been assigned to. This

would be a “UA” Unknown Alarm followed by the zone number and text if SIA

extended is selected. It will also send an SMS to the end user and engineer if

select to do so when the unconfirmed alarm filter is selected.

Tech Zone Display

Allows an opening zone to be displayed on the system keypad. The alert led

should also activate. When areas are selected it will only be displayed on the

keypad which is assigned to the area in which the zone has been selected.

The alert may only be displayed on the keypad when the area is in the unset

mode and not in the Part A, Part B and set mode.

Tech Zone Audible

Allows an activated zone to operate the buzzer. This will operate the same as

the Tech Zone Display in the different setting modes and on systems with

areas.

Tech Zone Delay

Allows the zone to have a programmable delay. The delay is variable from 0

to 9999 seconds and will apply to all Tech Zones. The operation is the same

as the Mains Delay timer, if the zone is closed within the delay time, then no

alarm is sent to the ARC, no SMS is sent to the user and the Technical

Output will not trip.

1 2 ... 283 284 285 286 287 288 289 290 291 292 293 294 295 296

Siemens SPCK421 Especificaciones Pagina 288

Comentarios a estos manuales

Siemens SPCK421 Especificaciones Pagina 288

Comentarios a estos manuales

Relacionado con productos y manuales para Teclados numéricos Siemens SPCK421