Siemens SIMATIC TI500 Especificaciones Pagina 93
- Pagina / 322
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-10
Installing 575 System Hardware SIMATIC 545/555/575 System Manual
4.6 Installing the PPX:575–2130 VMEbus Base
Figure 4-4 shows the physical dimensions of the PPX:575–2130 VMEbus
base. This base is designed to be mounted and operated in the horizontal
orientation only.
12.22
(310)
19.0 (483)
17.68 (449)
Optional fan assembly
9.58 (243)
Measurements: in. (mm)
Figure 4-4 VMEbus Base Physical Measurements
The VMEbus base conforms to DIN 41494 and IEC 297 standards which
define the requirements for equipment mounted in standard 19-inch rack
cabinets. The base is a 7U high (12.25-in.) unit. Figure 4-5 shows the
measurements required for front panel or 19-inch cabinet mounting. Leave
clearance of at least 3 inches above and below the base for cooling.
You must remove the rear mounting brackets and the ground lug in order to
install the unit in a 19-inch rack or the front panel cutout shown in
Figure 4-5. After installing the base, re-install the ground lug to the side of
the base to provide a proper grounding connection. (Refer to Chapter 2,
Figure 2-14, for proper placement of the grounding lug.)
12.25
(311)
18.31 (465)
17.72 (450)
0.272
(6.9)
8 holes
3.50 (89)
3.50 (89)
2.25 (57)
1.50 (38)
0.295
(7.5)
diameter
Measurements: in. (mm)
Figure 4-5 19″ Rack or Front Panel Mounting Measurements for Base
Mechanical
Outline
Mounting
Measurements
- 1
- 1
- MANUAL PUBLICATION HISTORY 3
- LIST OF EFFECTIVE PAGES 4
- Contents 5
- Contents v 7
- Contents vii 9
- Contents ix 11
- Chapter 9 Troubleshooting 12
- Contents xi 13
- List of Figures 15
- Contents xv 17
- List of Tables 18
- Contents xvii 19
- System Overview 23
- 1.1 Overview 24
- Overview (continued) 26
- 1.2 System Features 28
- Table 1-2 CPU Specifications 29
- System Features (continued) 30
- 1.3 Programming Tools 33
- 1.4 Hardware Overview 34
- Pre-installation Guidelines 36
- 2.2 Safety Considerations 38
- 2.3 575 Fault Relay Operation 41
- USER-CONFIGURED 42
- 2.5 Electrical Noise 47
- 2.6 Correcting Noise Problems 48
- 2.7 Wiring Guidelines 51
- Chapter 3 56
- To install a CPU: 57
- To install an RBC: 57
- 3.3 Series 505 Bases 59
- Measurements: 62
- TAB1TAB2 64
- DC POWER GOOD 66
- AC NEUTRAL 66
- 505-6660 66
- Replaceable Lithium Battery 71
- Replaceable 73
- Lithium Battery 73
- Battery Clip 73
- Battery Socket 73
- 0 (Off)(On) 1 77
- Maximum torque: 82
- 5.0 in-lb (0.56 N-m) 82
- Chapter 4 84
- • Series 505 Remote I/O Annex 85
- • PROFIBUS-DP Annex 85
- Front of Fan Assembly 91
- Fuse holder 92
- Turn counterclockwise 92
- (Run mode) 4.875 to 5.250 1 A 98
- (Battery 98
- Align metal backplate 100
- 4.8 Installing the Battery 103
- Battery connector 104
- Rear panel 104
- Break-away tab 104
- Battery fuse 105
- Alignment 106
- Alignment notch 106
- 4.10 Configuring the CPU 107
- Dipswitch 112
- Standoff 112
- 4.12 Installing VMEbus Boards 115
- 575 system 116
- Figure 4-18 575 Controller 116
- 4.13 Wiring the Fault Relay 127
- *optional 128
- Chapter 5 142
- 5.1 Overview 143
- 5.2 Installation 144
- Installation (continued) 145
- 5.3 Communication Ports 146
- Dipswitch for 149
- Backplane 149
- Figure 5-8 RBC Status Display 153
- Table 5-4 RBC Status Codes 153
- Status Display 153
- 5.5 PPX:505–6870 RBC 155
- Jumper E1 for 156
- PPX:505–6870 RBC (continued) 157
- Cabling and Wiring the System 166
- 6.1 Cable Routing 167
- Drop line from CPU or RBC 180
- Terminating 180
- Resistor 180
- 6.4 Connecting Modems 197
- 6.5 Connecting to a Printer 199
- Chapter 7 201
- 7.1 Program Storage Options 202
- Note location of notches 207
- Note location 207
- Starting Up the System 213
- 8.1 Powering Up the System 214
- 8.2 CPU Memory Configuration 216
- Number per block 217
- Troubleshooting 221
- System Specifications 246
- ° C (32 to 140° F) 247
- ° C (–40 to 158° F) 247
- Power and Compatibility 251
- B.1 Power Consumption 252
- Power Consumption (continued) 254
- Serial Number 259
- Appendix C 260
- Upgrade Path A 264
- Upgrade Path B 264
- Upgrade Path 266
- Remote Base Controller 272
- Power Supply 272
- FREEZE 273
- (factory set) 273
- Controller 275
- RS-485 I/O 282
- From PLC 282
- I/O BASES 282
- 505–6860 282
- Series 505 and VME Components 283
- D.2 575 VME System Components 287
- D.3 Recommended Spare Parts 288
- Appendix E 290
- E.1 Discrete AC Input Module 291
- E.3 Discrete AC Output Module 296
- °C) Temperature (°C) 297
- E.5 Discrete DC Output Module 301
- E.6 Discrete DC Input Module 304
- Appendix F 306
- Index-2 313
- Index-4 315
- Index-6 317
- Index-8 319
- Index-10 321
Relacionado con productos y manuales para Gateways / Controladores Siemens SIMATIC TI500
(94 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales