Siemens SIMATIC TI500 Especificaciones Pagina 252
- Pagina / 322
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Power and Compatibility
B-2
SIMATIC 545/555/575 System Manual
B.1 Power Consumption
Table B-1 shows the power consumption of 545 and 555 CPUs, with and
without PROFIBUS-DP annex cards. Table B-2 shows the power
consumption of 575 CPUs, with or without an annex card. (The Series 505
remote I/O and PROFIBUS-DP I/O annex cards have the same effect on
power consumption.)
Table B-1 545/555 CPU Power Consumption
Without PROFIBUS-DP Annex Card With PROFIBUS-DP Annex Card
CPU Model
+5 V –5 V +5 V –5 V
545–1103/–1105 4 W (0.8 A) 0.20 W (.04 A) 8.5 W (1.7 A) 0.20 W (.04 A)
545–1104/–1106 Not applicable Not applicable 8.5 W (1.7 A) 0.20 W (.04 A)
555–1103/–1104 Not applicable Not applicable 8.5 W (1.7 A) 0.20 W (.04 A)
555–1105/–1106* Not applicable Not applicable 8.5 W (1.7 A) 0.20 W (.04 A)
Note: Power consumption given in watts (amps in parentheses).
*PROFIBUS-DP communication port built into 555–1105 and –1106 CPU board.
Table B-2 575–2104 CPU Power Consumption
Voltage
Power Consumption without
Either Annex Card
Power Consumption with Either
Annex Card
+5 V 11 W (2.2 A) 16 W (3.2 A)
+12 V 600 mW (50 mA) 600 mW (50 mA)
–12 V 600 mW (50 mA) 600 mW (50 mA)
V
batt
(+5 V STDBY)
600 mW (120 mA)
1 mA in backup
600 mW (120 mA)
1 mA in backup
Note: Power consumption given in watts (amps in parentheses).
All current Series 505 power supply modules can supply up to 55 watts of
power to the modules listed in Table B-3.
You can increase the available power by using two power supplies in the
505–6511 Redundant Base for a total of 90 watts if the redundant mode is
not required. In this case, if one power supply module fails, the other power
supply module trips off as well when the actual load is above its 55 watt
capacity.
Influence of Annex
Cards on CPU
Power
Consumption
Power Supply
Loading
- 1
- 1
- MANUAL PUBLICATION HISTORY 3
- LIST OF EFFECTIVE PAGES 4
- Contents 5
- Contents v 7
- Contents vii 9
- Contents ix 11
- Chapter 9 Troubleshooting 12
- Contents xi 13
- List of Figures 15
- Contents xv 17
- List of Tables 18
- Contents xvii 19
- System Overview 23
- 1.1 Overview 24
- Overview (continued) 26
- 1.2 System Features 28
- Table 1-2 CPU Specifications 29
- System Features (continued) 30
- 1.3 Programming Tools 33
- 1.4 Hardware Overview 34
- Pre-installation Guidelines 36
- 2.2 Safety Considerations 38
- 2.3 575 Fault Relay Operation 41
- USER-CONFIGURED 42
- 2.5 Electrical Noise 47
- 2.6 Correcting Noise Problems 48
- 2.7 Wiring Guidelines 51
- Chapter 3 56
- To install a CPU: 57
- To install an RBC: 57
- 3.3 Series 505 Bases 59
- Measurements: 62
- TAB1TAB2 64
- DC POWER GOOD 66
- AC NEUTRAL 66
- 505-6660 66
- Replaceable Lithium Battery 71
- Replaceable 73
- Lithium Battery 73
- Battery Clip 73
- Battery Socket 73
- 0 (Off)(On) 1 77
- Maximum torque: 82
- 5.0 in-lb (0.56 N-m) 82
- Chapter 4 84
- • Series 505 Remote I/O Annex 85
- • PROFIBUS-DP Annex 85
- Front of Fan Assembly 91
- Fuse holder 92
- Turn counterclockwise 92
- (Run mode) 4.875 to 5.250 1 A 98
- (Battery 98
- Align metal backplate 100
- 4.8 Installing the Battery 103
- Battery connector 104
- Rear panel 104
- Break-away tab 104
- Battery fuse 105
- Alignment 106
- Alignment notch 106
- 4.10 Configuring the CPU 107
- Dipswitch 112
- Standoff 112
- 4.12 Installing VMEbus Boards 115
- 575 system 116
- Figure 4-18 575 Controller 116
- 4.13 Wiring the Fault Relay 127
- *optional 128
- Chapter 5 142
- 5.1 Overview 143
- 5.2 Installation 144
- Installation (continued) 145
- 5.3 Communication Ports 146
- Dipswitch for 149
- Backplane 149
- Figure 5-8 RBC Status Display 153
- Table 5-4 RBC Status Codes 153
- Status Display 153
- 5.5 PPX:505–6870 RBC 155
- Jumper E1 for 156
- PPX:505–6870 RBC (continued) 157
- Cabling and Wiring the System 166
- 6.1 Cable Routing 167
- Drop line from CPU or RBC 180
- Terminating 180
- Resistor 180
- 6.4 Connecting Modems 197
- 6.5 Connecting to a Printer 199
- Chapter 7 201
- 7.1 Program Storage Options 202
- Note location of notches 207
- Note location 207
- Starting Up the System 213
- 8.1 Powering Up the System 214
- 8.2 CPU Memory Configuration 216
- Number per block 217
- Troubleshooting 221
- System Specifications 246
- ° C (32 to 140° F) 247
- ° C (–40 to 158° F) 247
- Power and Compatibility 251
- B.1 Power Consumption 252
- Power Consumption (continued) 254
- Serial Number 259
- Appendix C 260
- Upgrade Path A 264
- Upgrade Path B 264
- Upgrade Path 266
- Remote Base Controller 272
- Power Supply 272
- FREEZE 273
- (factory set) 273
- Controller 275
- RS-485 I/O 282
- From PLC 282
- I/O BASES 282
- 505–6860 282
- Series 505 and VME Components 283
- D.2 575 VME System Components 287
- D.3 Recommended Spare Parts 288
- Appendix E 290
- E.1 Discrete AC Input Module 291
- E.3 Discrete AC Output Module 296
- °C) Temperature (°C) 297
- E.5 Discrete DC Output Module 301
- E.6 Discrete DC Input Module 304
- Appendix F 306
- Index-2 313
- Index-4 315
- Index-6 317
- Index-8 319
- Index-10 321
Relacionado con productos y manuales para Gateways / Controladores Siemens SIMATIC TI500
(94 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales