Siemens SIMATIC TI500 Especificaciones Pagina 108
- Pagina / 322
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-25
SIMATIC 545/555/575 System Manual
Installing 575 System Hardware
Table 4-3 lists the configuration options you can select using the dipswitch
on the CPU board (575–2105/–2106 CPUs) or on an HSIO annex card or a
PROFIBUS-DP annex card when used with a 575–2104 CPU. These options
are explained in more detail on the following two pages.
Table 4-3 Dipswitch Configuration Options
Switch
Switch
Position
Description
On – On For 575–2126 annex card, selects remote I/O baud rate. Do not change.
1 – 2
Off – Off For 505–CP5434–DP annex card, reserved for factory use. Do not change.
BASE ADDRESS selections: These dipswitches select the base address for the 575 system tables
(A24 address space) and global control and status registers (A16 address space). Section 4.15
describes how the 575 allocates VMEbus memory.
A24 Base Address A16 Base Address
3 – 4
On – On 000000
16
0000
16
(Assumed value if AUTO-CONFIGURED.)
On – Off 400000
16
4000
16
Off – On 800000
16
8000
16
Off – Off C00000
16
C000
16
5
On
ASSERT/WAIT FOR SYSRESET* to recover from FAULT. If the primary 575 is in
slot 1 (only a 575 primary residing in slot 1 can issue SYSRESET*), it issues
SYSRESET* during FAULT recovery. The 575 secondaries do not recover from
FAULT mode unless SYSRESET* is issued. (AUTO-CONFIGURED value.)
5
Off
DO NOT ASSERT/WAIT FOR SYSRESET* to recover from FAULT. The 575 primary
coordinates FAULT recovery with the 575 secondaries without issuing
SYSRESET*.
On
AUTO-CONFIGURED — SW3 through SW5 and SW7 are ignored. This option
allows compatibility with earlier releases (that is, with 575 Release 2.0
through 575 Release 3.0).
6
Off
USER-CONFIGURED — configuration in SW3 through SW5 and SW7. If this
option is selected, then any 575–2104 CPU must have a remote I/O annex
card, and switches SW3 through SW6 must be set to the same position.
7
On
PRIMARY-575 — Only one 575 CPU can be configured as a primary. All other
575s must be configured as secondaries. If a 575 CPU is in slot 1, then it is
configured as the primary, regardless of the switch position.
Off
SECONDARY-575
On AUTO RECOMPILE function disabled.*
8
Off AUTO RECOMPILE function enabled.*
*Available on CPU models 575–2105/–2106 Release 5.1 or greater. Refer to Appendix F for more information
about the Auto Recompile function.
- 1
- 1
- MANUAL PUBLICATION HISTORY 3
- LIST OF EFFECTIVE PAGES 4
- Contents 5
- Contents v 7
- Contents vii 9
- Contents ix 11
- Chapter 9 Troubleshooting 12
- Contents xi 13
- List of Figures 15
- Contents xv 17
- List of Tables 18
- Contents xvii 19
- System Overview 23
- 1.1 Overview 24
- Overview (continued) 26
- 1.2 System Features 28
- Table 1-2 CPU Specifications 29
- System Features (continued) 30
- 1.3 Programming Tools 33
- 1.4 Hardware Overview 34
- Pre-installation Guidelines 36
- 2.2 Safety Considerations 38
- 2.3 575 Fault Relay Operation 41
- USER-CONFIGURED 42
- 2.5 Electrical Noise 47
- 2.6 Correcting Noise Problems 48
- 2.7 Wiring Guidelines 51
- Chapter 3 56
- To install a CPU: 57
- To install an RBC: 57
- 3.3 Series 505 Bases 59
- Measurements: 62
- TAB1TAB2 64
- DC POWER GOOD 66
- AC NEUTRAL 66
- 505-6660 66
- Replaceable Lithium Battery 71
- Replaceable 73
- Lithium Battery 73
- Battery Clip 73
- Battery Socket 73
- 0 (Off)(On) 1 77
- Maximum torque: 82
- 5.0 in-lb (0.56 N-m) 82
- Chapter 4 84
- • Series 505 Remote I/O Annex 85
- • PROFIBUS-DP Annex 85
- Front of Fan Assembly 91
- Fuse holder 92
- Turn counterclockwise 92
- (Run mode) 4.875 to 5.250 1 A 98
- (Battery 98
- Align metal backplate 100
- 4.8 Installing the Battery 103
- Battery connector 104
- Rear panel 104
- Break-away tab 104
- Battery fuse 105
- Alignment 106
- Alignment notch 106
- 4.10 Configuring the CPU 107
- Dipswitch 112
- Standoff 112
- 4.12 Installing VMEbus Boards 115
- 575 system 116
- Figure 4-18 575 Controller 116
- 4.13 Wiring the Fault Relay 127
- *optional 128
- Chapter 5 142
- 5.1 Overview 143
- 5.2 Installation 144
- Installation (continued) 145
- 5.3 Communication Ports 146
- Dipswitch for 149
- Backplane 149
- Figure 5-8 RBC Status Display 153
- Table 5-4 RBC Status Codes 153
- Status Display 153
- 5.5 PPX:505–6870 RBC 155
- Jumper E1 for 156
- PPX:505–6870 RBC (continued) 157
- Cabling and Wiring the System 166
- 6.1 Cable Routing 167
- Drop line from CPU or RBC 180
- Terminating 180
- Resistor 180
- 6.4 Connecting Modems 197
- 6.5 Connecting to a Printer 199
- Chapter 7 201
- 7.1 Program Storage Options 202
- Note location of notches 207
- Note location 207
- Starting Up the System 213
- 8.1 Powering Up the System 214
- 8.2 CPU Memory Configuration 216
- Number per block 217
- Troubleshooting 221
- System Specifications 246
- ° C (32 to 140° F) 247
- ° C (–40 to 158° F) 247
- Power and Compatibility 251
- B.1 Power Consumption 252
- Power Consumption (continued) 254
- Serial Number 259
- Appendix C 260
- Upgrade Path A 264
- Upgrade Path B 264
- Upgrade Path 266
- Remote Base Controller 272
- Power Supply 272
- FREEZE 273
- (factory set) 273
- Controller 275
- RS-485 I/O 282
- From PLC 282
- I/O BASES 282
- 505–6860 282
- Series 505 and VME Components 283
- D.2 575 VME System Components 287
- D.3 Recommended Spare Parts 288
- Appendix E 290
- E.1 Discrete AC Input Module 291
- E.3 Discrete AC Output Module 296
- °C) Temperature (°C) 297
- E.5 Discrete DC Output Module 301
- E.6 Discrete DC Input Module 304
- Appendix F 306
- Index-2 313
- Index-4 315
- Index-6 317
- Index-8 319
- Index-10 321
Relacionado con productos y manuales para Gateways / Controladores Siemens SIMATIC TI500
(94 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales