Siemens SIMATIC TI500 Especificaciones Pagina 109
- Pagina / 322
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-26
Installing 575 System Hardware SIMATIC 545/555/575 System Manual
Configuring the CPU (continued)
When SW6 is set to the On position, the CPU is in the AUTO-CONFIGURED
mode.
• In the
AUTO-CONFIGURED mode, the 575 Release 5.0 is compatible with
575 Releases 2.0 through 3.1.
• In AUTO-CONFIGURED mode, a 575 CPU must be located in slot 1.
During FAULT recovery, the 575 CPU in slot 1 issues SYSRESET*.
NOTE: If any 575–2104 CPU in your system does not have a remote I/O
annex card, then the entire system must operate in the
AUTO-CONFIGURED
mode. Verify that the 575–2104 CPUs in your system that do have an annex
card have SW6 set to the On position; you do not need to do anything to the
rest of the switches.
To select the USER-CONFIGURED mode, you must ensure that SW6 is in the
Off position for every dipswitch, and that SW3 through SW6 are set to the
same positions for every 575 in the system. (575–2104 CPUs require an I/O
annex card in order to select user-configured mode.)
In the
USER-CONFIGURED mode, the position of switch SW7 determines
whether the CPU is a primary or secondary 575. Setting SW7 to the On
position indicates that the CPU is the primary 575 in the system; setting
SW7 to the Off position indicates that the CPU is a secondary 575.
Only one 575 can be the primary 575 in a system. If a 575 CPU resides in
slot 1 (the system-controller slot), then it is automatically configured as the
primary 575 CPU, regardless of the position of SW7. Do not configure any
other 575 as your primary.
Switch 8 is used to allow the CPU to perform an Auto Recompile during
runtime. Switch 8 is shipped in the disabled (left) position. To activate this
feature, set the switch to the right (enabled) position. Refer to Appendix F
for more information about the Auto Recompile function.
Using the
AUTO-CONFIGURED
Mode
Using the
USER-CONFIGURED
Mode
Configuring the 575
Primary and
Secondaries
Enabling the
Auto Recompile
Function
- 1
- 1
- MANUAL PUBLICATION HISTORY 3
- LIST OF EFFECTIVE PAGES 4
- Contents 5
- Contents v 7
- Contents vii 9
- Contents ix 11
- Chapter 9 Troubleshooting 12
- Contents xi 13
- List of Figures 15
- Contents xv 17
- List of Tables 18
- Contents xvii 19
- System Overview 23
- 1.1 Overview 24
- Overview (continued) 26
- 1.2 System Features 28
- Table 1-2 CPU Specifications 29
- System Features (continued) 30
- 1.3 Programming Tools 33
- 1.4 Hardware Overview 34
- Pre-installation Guidelines 36
- 2.2 Safety Considerations 38
- 2.3 575 Fault Relay Operation 41
- USER-CONFIGURED 42
- 2.5 Electrical Noise 47
- 2.6 Correcting Noise Problems 48
- 2.7 Wiring Guidelines 51
- Chapter 3 56
- To install a CPU: 57
- To install an RBC: 57
- 3.3 Series 505 Bases 59
- Measurements: 62
- TAB1TAB2 64
- DC POWER GOOD 66
- AC NEUTRAL 66
- 505-6660 66
- Replaceable Lithium Battery 71
- Replaceable 73
- Lithium Battery 73
- Battery Clip 73
- Battery Socket 73
- 0 (Off)(On) 1 77
- Maximum torque: 82
- 5.0 in-lb (0.56 N-m) 82
- Chapter 4 84
- • Series 505 Remote I/O Annex 85
- • PROFIBUS-DP Annex 85
- Front of Fan Assembly 91
- Fuse holder 92
- Turn counterclockwise 92
- (Run mode) 4.875 to 5.250 1 A 98
- (Battery 98
- Align metal backplate 100
- 4.8 Installing the Battery 103
- Battery connector 104
- Rear panel 104
- Break-away tab 104
- Battery fuse 105
- Alignment 106
- Alignment notch 106
- 4.10 Configuring the CPU 107
- Dipswitch 112
- Standoff 112
- 4.12 Installing VMEbus Boards 115
- 575 system 116
- Figure 4-18 575 Controller 116
- 4.13 Wiring the Fault Relay 127
- *optional 128
- Chapter 5 142
- 5.1 Overview 143
- 5.2 Installation 144
- Installation (continued) 145
- 5.3 Communication Ports 146
- Dipswitch for 149
- Backplane 149
- Figure 5-8 RBC Status Display 153
- Table 5-4 RBC Status Codes 153
- Status Display 153
- 5.5 PPX:505–6870 RBC 155
- Jumper E1 for 156
- PPX:505–6870 RBC (continued) 157
- Cabling and Wiring the System 166
- 6.1 Cable Routing 167
- Drop line from CPU or RBC 180
- Terminating 180
- Resistor 180
- 6.4 Connecting Modems 197
- 6.5 Connecting to a Printer 199
- Chapter 7 201
- 7.1 Program Storage Options 202
- Note location of notches 207
- Note location 207
- Starting Up the System 213
- 8.1 Powering Up the System 214
- 8.2 CPU Memory Configuration 216
- Number per block 217
- Troubleshooting 221
- System Specifications 246
- ° C (32 to 140° F) 247
- ° C (–40 to 158° F) 247
- Power and Compatibility 251
- B.1 Power Consumption 252
- Power Consumption (continued) 254
- Serial Number 259
- Appendix C 260
- Upgrade Path A 264
- Upgrade Path B 264
- Upgrade Path 266
- Remote Base Controller 272
- Power Supply 272
- FREEZE 273
- (factory set) 273
- Controller 275
- RS-485 I/O 282
- From PLC 282
- I/O BASES 282
- 505–6860 282
- Series 505 and VME Components 283
- D.2 575 VME System Components 287
- D.3 Recommended Spare Parts 288
- Appendix E 290
- E.1 Discrete AC Input Module 291
- E.3 Discrete AC Output Module 296
- °C) Temperature (°C) 297
- E.5 Discrete DC Output Module 301
- E.6 Discrete DC Input Module 304
- Appendix F 306
- Index-2 313
- Index-4 315
- Index-6 317
- Index-8 319
- Index-10 321
Relacionado con productos y manuales para Gateways / Controladores Siemens SIMATIC TI500
(94 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales