Siemens ET 7Y Series Especificaciones Pagina 81
- Pagina / 214
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DP Master Module
6-5
ET 200S IM 151-7 CPU Interface Module
A5E00058783-04
Start-up of the IM 151-7 CPU as a DP master
When it starts up, the IM 151-7 CPU compares the preset configuration of the DP
master system with the actual configuration.
If the preset configuration the actual configuration, the CPU goes into RUN
mode.
If the preset configuration the actual configuration, the behavior of the CPU
depends on the setting of the Start-up when the preset configuration 0 actual
configuration parameter.
Start-up when preset configuration 0
actual configuration + yes
(default setting)
Start-up when preset configuration 0
actual configuration + no
IM 151-7 CPU goes into RUN mode.
(BF-LED on the DP master module flashes
if all DP slaves cannot be addressed.)
IM 151-7 CPU remains in STOP mode and
the BF-LED on the DP master module
flashes after the set Monitoring time for
transfer of parameters to modules has
elapsed.
A flashing BF-LED indicates that at least
one DP slave cannot be addressed. Check
whether all DP slaves are switched on and
that they correspond to the defined
configuration, or read out the diagnostic
buffer using STEP 7.
Recognizing the operating modes of the DP slave (event recognition)
The table below shows how the IM 151-7 CPU identifies changes in operating
mode and interruptions in data transfer as a DP master.
Table 6-1 Event recognition of the IM 151-7 CPU as a DP master
Event
What takes place in the DP master?
Bus interruption
(short-circuit,
connector
removed)
OB 86 is called and Station failure is reported
(incoming event; diagnosis address of the DP slave assigned to
the DP master)
In the case of I/O access: OB 122 is called
(I/O access error)
DP slave:
RUN → STOP
OB 82 is called and Module malfunction reported
(incoming event; diagnosis address of the DP slave assigned to
the DP master; variable OB82_MDL_STOP=1)
DP slave:
STOP → RUN
OB 82 is called and Module ok reported.
(outgoing event; diagnosis address of the DP slave assigned to
the DP master; variable OB82_MDL_STOP=0)
Tip:
Always program OB 82 and OB 86 when commissioning the CPU as a DP master.
This will allow you to detect and evaluate the faults and interruptions during data
transfer.
- Drawing number 1
- Qualified Personnel 2
- Correct Usage 2
- Trademarks 2
- Safety Guidelines 2
- Purpose of the manual 3
- Required level of knowledge 3
- Guide to the manual 6
- Special note 6
- Recycling and disposal 6
- Additional support 7
- Training center 8
- A&D Technical Support 8
- A5E00058783-04 10
- Contents 11
- Product Overview 19
- What is the IM 151-7 CPU? 20
- IM 151-7 CPU 21
- ET 200S fail-safe modules 26
- Getting Started 27
- Required material and tools 28
- Return 35
- 2.6 6th step: Test Run 36
- Set the slave address to 4 38
- Click on the New button; 38
- S7-300 CPU 42
- ResultAction 43
- IM 151-7 CPU and S7-300 45
- Diagnosis and troubleshooting 48
- Other manuals 48
- Addressing 49
- Slot Assignment 50
- Address Assignment 51
- Advantages 53
- Data consistency 54
- Access in the user program 55
- Rules for address allocation 56
- Sample Program 57
- S5 DP master 58
- Introduction 59
- Equidistance 59
- DP master functionality 59
- Access to the ET 200S 61
- 4.2 Network components 64
- 4.3 PROFIBUS address 66
- 4.4 Functions via the PD/OP 67
- Force test function 68
- Application example 69
- 4.5 Direct communication 70
- ET 200S in the MPI Network 73
- Structure of an MPI network 74
- Transmission rates 74
- Network components 74
- 5.2 MPI address 75
- DP Master Module 77
- Procedure 78
- Commissioning 79
- Stand-alone (MPI) 84
- IM 151-7 CPU as S7 slave 84
- Prerequisite 85
- How do you reset the memory? 86
- Commissioning the ET 200S 89
- Loading the user program 90
- Start-up 90
- 7.4 Diagnostics using LEDs 91
- Diagnostic addresses 94
- 7.6.1 Station status 1 to 3 98
- Station status 2 99
- Station status 3 99
- 7.6.2 Master PROFIBUS address 100
- 7.6.3 Manufacturer ID 100
- 7.6.4 Module diagnostics 101
- 7.6.5 Module status 102
- Structure 103
- 7.6.6 Interrupt status 104
- Commissioning and Diagnostics 106
- In this section 107
- More detailed information 107
- Bytes 0 and 1 109
- Module classes 109
- Bytes 2 and 3 109
- Bytes 4 to 7 110
- Single fault of a channel 111
- Functions of the IM 151-7 CPU 113
- 8.1 Data for the PROFIBUS-DP 114
- Mode selector 116
- 8.3 SIMATIC Micro Memory Card 118
- Service life of an MMC 119
- 6ES7 953Ć8Lx00Ć0AA0 121
- Firmware update with MMC 122
- 8.4 Memory concept 124
- Working memory 125
- System memory 125
- Retentivity 125
- Erasing blocks 128
- Uploading 128
- Compression 129
- Promming (RAM to ROM) 129
- Removing/inserting the MMC 130
- Memory reset 131
- Restart (warm restart) 131
- 8.4.3 Address areas 132
- Cycle time 133
- Local data 134
- 8.4.4 Handling data in DBs 135
- Measured value archives 136
- MMC access 137
- 8.5 Interfaces 138
- 8.6 Clock 140
- 8.7 S7 connections 141
- Assigning S7 connections 142
- 8.8 Communication 146
- OP communication 147
- S7 basic communication 147
- S7 communication 147
- Global data communication 148
- GD resources 149
- 8.9 Routing 150
- Prerequisites 151
- More information 152
- 8.10 Data consistency 153
- 8.11 Blocks 154
- 8.12 Parameters 156
- RTD-4L Pt 100 158
- Reference 159
- Exceptions 160
- Cycle and Response Times 165
- 9.1 Cycle time 166
- Extending the cycle time 167
- Process image transfer time 167
- User program scanning time: 168
- 9.2 Response time 169
- Shortest response time 170
- Calculation 170
- Longest response time 171
- 9.3 Interrupt response time 172
- Technical Specifications 173
- Order numbers 174
- Features 174
- SFC 20 ”BLKMOV” 182
- SFC 54 ”RD_DPARM” 182
- PD/OP functions 184
- Chapter overview 187
- More information 187
- 12.2 Porting the user program 189
- Porting with packed addresses 190
- Rewiring 190
- Glossary 193
- Diagnostic buffer 195
- Diagnostic interrupt 195
- Direct Communication 195
- Distributed I/O Systems 195
- DP Master 195
- FC Function 197
- Function 197
- Transmission rate 204
- User memory 204
- User program 204
- Working Memory 204
- Product information for 211
- 147Ć1AA11Ć0XB0) 211
- 147Ć2AA01Ć0XB0) 211
- 147Ć2AB01Ć0XB0) 211
- 151Ć7AA11Ć0AB0) 211
- A5E00385826-02 212
- Copyright 2006 by Siemens AG 213
- A5E00860829-01 213
Relacionado con productos y manuales para Placas Siemens ET 7Y Series
Placas Siemens EH8..TE1.. Manual de usuario
(77 paginas)
(77 paginas)
Placas Siemens ET1 Series Información técnica
(26 paginas)
(26 paginas)
Placas Siemens EF 711 Series Guía de usuario
(492 paginas)
(492 paginas)
Placas Siemens EF 725 Series Manual de usuario
(12 paginas)
(12 paginas)
Placas Siemens ET 783 Series Guía de usuario
(40 paginas)
(40 paginas)
Placas Siemens EH6..MB1.. Manual de usuario
(218 paginas)
Placas Siemens EF 847 Series Manual de servicio
(46 paginas)
(46 paginas)
Placas Siemens CA 373 Series Manual de servicio
(27 paginas)
(27 paginas)
Placas Siemens PVN 875 Series Especificaciones
(34 paginas)
(34 paginas)
Placas Siemens NAN 67 Series Manual de usuario
(76 paginas)
(76 paginas)
Placas Siemens TL.. Instrucciones de operaciones
(42 paginas)
(42 paginas)
Placas Siemens CM343 Series Manual de servicio
(140 paginas)
(140 paginas)
Placas Siemens EF 784 Series Manual de usuario
(9 paginas)
(9 paginas)
Placas Siemens ET 727 Series Manual de usuario
(11 paginas)
(11 paginas)
Placas Siemens EI645EC11 Manual de reparación
(122 paginas)
(122 paginas)
Placas Siemens EF 7850 Series Especificaciones
(38 paginas)
(38 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.257 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales