Siemens Pacemaker UM344-2 Manual de usuario Pagina 71
- Pagina / 183
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
UM344-2 ON-LINE AND OFF-LINE OPERATION
September 1995
5
-
1
5.0 ON-LINE AND OFF-LINE OPERATION
On-line operation is any configuration or monitoring activity which involves direct communication with a
transmitter. When the controller function block is disabled, the local pushbuttons may be used to configure
range and damping. When the controller is enabled, the local pushbuttons may be used to display
PROCESS VARIABLE (PV), SETPOINT (SP) and VALVE (V); transfer control mode from AUTO
(A) to MANUAL (M); and change or store SET POINT and VALVE settings.
The configuration may be edited remotely using an MXC, a personal computer (PC) running XTC
Configuration Software, or another HART Primary or Secondary Master. The MXC can also be used to
monitor a transmitter’s variables and to look at a transmitter’s status.
Off-line operation is any configuration activity that occurs without direct communication with a transmitter.
This includes using the MXC to create or edit a configuration and then to store that configuration in an
MXC archive. It also includes using a personal computer and XTC Configuration Software to create or
edit, and then store, a configuration.
5.1 ON-LINE OPERATION
The first part of this section contains the steps to configure and monitor a Model 344 from an MXC. The
latter part of this section describes configuring the transmitter using the local pushbuttons.
5.1.1 Using the MXC for Configuration
Each transmitter is shipped with default data stored in its memory. Some of this data controls communi-
cation and transmitter operation and cannot be altered by the user. Other data determines how the
transmitter responds to changes in temperature with a change in current or digital output and is alterable
by the user. Using the MXC in the on-line mode, configurations can be uploaded from the transmitter,
edited, and saved to archive memory or downloaded to the Model 344. The following sections describe
configuration in more detail.
The following sections are in a two column format. Step-by-step procedures are in the right column. The
left column contains relevant MXC screens.
- USER’S MANUAL 1
- TABLE OF CONTENTS 2
- CONTENTS UM344-2 3
- September 1995 3
- UM344-2 CONTENTS 4
- September 1995 4
- SECTION AND TITLE PAGE 5
- LIST OF ILLUSTRATIONS 6
- LIST OF TABLES 7
- 1.0 INTRODUCTION 10
- FIGURE 1-1 Basic Model 344 11
- X02869S1 12
- 2.0 XTC COMMUNICATOR 14
- MOORE XTC COMMUNICATOR 15
- SELECT BLOCK TO EDIT 16
- - SENSOR INPUT 16
- PREV NEXT END ECT 16
- SELECT FUNCTION 18
- FIND ARCH TEST 18
- XMTR FUNC MXC END 18
- X02849S1 19
- LOOP OVERRIDE - CHOOSE 21
- CURRENT OUTPUT LEVEL 21
- 4 MA 20 MA OTHR END 21
- X02807S1 25
- SHORT OR LONG FORM 27
- ADDRESS? 27
- SHRT LONG 27
- ADDR ADDR POLL END 27
- MXC SELF TEST 28
- TEST TEST 28
- KEYS SCRN END 28
- WARNING! SELF TEST 30
- MAY BUMP TRANSMITTER 30
- OUTPUT A 30
- 4.0 INSTALLATION 35
- X02866S1 39
- X02867S1 40
- X02868S1 41
- X02817S1 42
- X02821S1 52
- Wall Mounting 53
- X02818S0 57
- FIGURE 4-8 Sensor Assembly 58
- X028AAS0 60
- X02870S1 61
- X02824S1 63
- TESTSIGNAL 66
- X02825S1 67
- MV LO : 0.0000 74
- ENTER MV LO: 74
- (F4) to change the setpoint 78
- DOWNLOADING 84
- CONFIGURATION 84
- - PLEASE WAIT 84
- DOWNLOAD 84
- COMPLETE 84
- MANUAL control mode to 92
- MANUAL control mode 92
- DG MR END CONT 96
- WARNING : ARCHIVE 97
- CONTAINS NO DATA 97
- A 97
- ERROR! ARCHIVE TYPE 98
- DOESN'T MATCH THE 98
- TRANSMITTER TYPE 98
- X02808S1 106
- X02827S1 1 of 2 111
- X02827S1 2 of 2 112
- APPLY 103.00 mV TO 115
- WITH COPPER WIRE 115
- CAL TEST END 118
- CALIBRATE / TEST 118
- TRANSMITTER PASSED 121
- TRANSMITTER SELFTEST 121
- 7.0 CIRCUIT DESCRIPTION 134
- Output Circuitry 135
- Input Circuitry 135
- X02815S0 142
- Z FS 146
- 9.0 GLOSSARY 154
- 4 - 20 mA 160
- Failsafe Level 160
- Absolute Alarm #1 161
- Absolute Alarm #2 161
- R = 162
- X02879S0 163
- Block Diagram, PD Controller 164
- Block Diagram, ID Controller 165
- X02881S1 168
- WARRANTY 177
- WARRANTY UM344-2 178
- W-2 October 1996 178
- PARTS LIST 179
- USER’S MANUAL ADDENDUM 181
- X03013S1 182
Relacionado con productos y manuales para De medición, control y control Siemens Pacemaker UM344-2
(22 paginas)
(22 paginas)
De medición, control y control Siemens BTC-BR Manual
(264 paginas)
(264 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales