Siemens Pacemaker UM344-2 Manual de usuario Pagina 30
- Pagina / 183
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
UM344-2 INITIAL TRANSMITTER SET-UP
September 1995
3
-
7
TEST SCRN - Press to test all screen segments.
When this key is pressed, the MXC displays the
"Begin" message to the left, then lights all the
segments, turns them all off, displays the
"Completed" message, and then returns to the
original test screen.
END - Press to exit the test mode and return to the
Main Menu screen.
3.3.2 Transmitter Testing
Although the Transmitter continuously performs an on-
line self test, a more extensive self test can be performed
after communication with the MXC has been established.
1. At the On-Line Menu, press CAL/TEST (F2) to
display the Calibrate and Test selections.
2. At the Calibrate/Test Menu, press TEST. A Test
caution screen will appear. Press one of the
following:
ABORT - Press to return to the Calibrate/Test
Menu.
PROCEED - Press to continue the self test. A
warning screen will be displayed then a message
states that the test is occurring. After the test, the
MXC will show whether or not the transmitter has
passed or failed the self test.
If the MXC indicates that the Transmitter has:
Passed - Press CONT then END.
Failed - Check installation wiring thoroughly. Go to
Section 6 for troubleshooting suggestions.
3. When the MXC displays the Transmitter’s ID (On-
Line Menu), press the STATUS Key to check for
Transmitter errors. If an error is present, the
ERROR Key (F2) will be displayed. Press
ERRORS (F2) to check for ROM, RAM, EEPROM,
TIMER and SENSOR errors. Refer to Section 6.3
Troubleshooting to confirm and resolve the error.
4. If the alarm function is enabled, press ALARM (F1)
to check the ALARM OUT OF SERVICE status.
MXC SCREEN TEST
ABOUT TO BEGIN
MXC SCREEN TEST
COMPLETED
TEST - PERFORMS
DIAGNOSTIC TEST ON
TRANS- A- PRO-
MITTER BORT CEED
CALIBRATE / TEST
CAL TEST END
WARNING! SELF TEST
MAY BUMP TRANSMITTER
OUTPUT A-
BORT CONT
TRANSMITTER PASSED
TRANSMITTER SELFTEST
CONT
- USER’S MANUAL 1
- TABLE OF CONTENTS 2
- CONTENTS UM344-2 3
- September 1995 3
- UM344-2 CONTENTS 4
- September 1995 4
- SECTION AND TITLE PAGE 5
- LIST OF ILLUSTRATIONS 6
- LIST OF TABLES 7
- 1.0 INTRODUCTION 10
- FIGURE 1-1 Basic Model 344 11
- X02869S1 12
- 2.0 XTC COMMUNICATOR 14
- MOORE XTC COMMUNICATOR 15
- SELECT BLOCK TO EDIT 16
- - SENSOR INPUT 16
- PREV NEXT END ECT 16
- SELECT FUNCTION 18
- FIND ARCH TEST 18
- XMTR FUNC MXC END 18
- X02849S1 19
- LOOP OVERRIDE - CHOOSE 21
- CURRENT OUTPUT LEVEL 21
- 4 MA 20 MA OTHR END 21
- X02807S1 25
- SHORT OR LONG FORM 27
- ADDRESS? 27
- SHRT LONG 27
- ADDR ADDR POLL END 27
- MXC SELF TEST 28
- TEST TEST 28
- KEYS SCRN END 28
- WARNING! SELF TEST 30
- MAY BUMP TRANSMITTER 30
- OUTPUT A 30
- 4.0 INSTALLATION 35
- X02866S1 39
- X02867S1 40
- X02868S1 41
- X02817S1 42
- X02821S1 52
- Wall Mounting 53
- X02818S0 57
- FIGURE 4-8 Sensor Assembly 58
- X028AAS0 60
- X02870S1 61
- X02824S1 63
- TESTSIGNAL 66
- X02825S1 67
- MV LO : 0.0000 74
- ENTER MV LO: 74
- (F4) to change the setpoint 78
- DOWNLOADING 84
- CONFIGURATION 84
- - PLEASE WAIT 84
- DOWNLOAD 84
- COMPLETE 84
- MANUAL control mode to 92
- MANUAL control mode 92
- DG MR END CONT 96
- WARNING : ARCHIVE 97
- CONTAINS NO DATA 97
- A 97
- ERROR! ARCHIVE TYPE 98
- DOESN'T MATCH THE 98
- TRANSMITTER TYPE 98
- X02808S1 106
- X02827S1 1 of 2 111
- X02827S1 2 of 2 112
- APPLY 103.00 mV TO 115
- WITH COPPER WIRE 115
- CAL TEST END 118
- CALIBRATE / TEST 118
- TRANSMITTER PASSED 121
- TRANSMITTER SELFTEST 121
- 7.0 CIRCUIT DESCRIPTION 134
- Output Circuitry 135
- Input Circuitry 135
- X02815S0 142
- Z FS 146
- 9.0 GLOSSARY 154
- 4 - 20 mA 160
- Failsafe Level 160
- Absolute Alarm #1 161
- Absolute Alarm #2 161
- R = 162
- X02879S0 163
- Block Diagram, PD Controller 164
- Block Diagram, ID Controller 165
- X02881S1 168
- WARRANTY 177
- WARRANTY UM344-2 178
- W-2 October 1996 178
- PARTS LIST 179
- USER’S MANUAL ADDENDUM 181
- X03013S1 182
Relacionado con productos y manuales para De medición, control y control Siemens Pacemaker UM344-2
(22 paginas)
(22 paginas)
De medición, control y control Siemens BTC-BR Manual
(264 paginas)
(264 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales