Siemens KDN Series Instrucciones de operaciones Pagina 67
- Pagina / 258
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
KINCO
67
4729H AT Setting
OFF: 0 (default), ON: 1. in the adjusting mode
4733H CT monitor value
Unit is 0.1A. in the running mode
DTB9696VR：Address and Content of Word Register (corresponds to 4X in the HMI)
Address Content Explanation
1000H Process value (PV) Measuring unit is 0.1, updated one time in 0.4 second
1001H Set point (SV) Unit is 0.1,
o
C or
o
F
1002H Upper-limit of temperature range
The data content should not be higher than the
temperature range. In the setting mode
1003H Lower-limit of temperature range
The data content should not be lower than the
temperature range. In the setting mode
1004H Input temperature sensor type
Please refer to the contents of the “Temperature Sensor
Type and Temperature Range” for detail. In the setting
mode
1005H Control method
0: PID, 1: ON/OFF, 2: manual tuning, 3: PID grogram
control. In the setting mode
1006H Heating/Cooling control selection
0: Heating, 1: Cooling, 2: Heating/Cooling, 3:
Cooling/Heating. In the setting mode
1007H
1st group of Heating/Cooling
control cycle
0 ~ 99, 0:0.5 sec. in the adjusting mode
or
1008H
2nd group of Heating/Cooling
control cycle
0 ~ 99, 0:0.5 sec. in the adjusting mode
1009H PB Proportional band
0.1 ~ 999.9. in the adjusting mode
100AH Ti Integral time
0~9999. in the adjusting mode
100BH Td Derivative time
0~9999. in the adjusting mode
100CH Integration default
0 ~ 100%, unit is 0.1%. in the adjusting mode
100DH
Proportional control offset error
value, when Ti = 0
0 ~ 100%, unit is 0.1%. in the adjusting mode
100EH
The setting of COEF when Dual
Loop output control are used
0.01 ~ 99.99, unit is 0.01 (setting when it is under the
control of PID ) in the adjusting mode
- CONTENTS 1
- Parallel Port Pin Definition 3
- Download Cable Diagram 10
- HMI Ethernet terminal 11
- Ethernet Hub or Switch 11
- RS232 12
- Allen-Bradley 14
- Serial System Communication 15
- Serial Communication Setting 16
- SLC500 RS232 communication 17
- PLC Software Setting 18
- Compactlogix L31 21
- PLC-5 RS232 cable diagram 23
- EtherNet cable 23
- ACS-Tech80 Motion Controller 24
- AysjNet 28
- Baumuller 33
- RS485-4 communication cable 33
- Bosch Rexroth 35
- PLC Software Settings 37
- L40 software setting 39
- Bosch Rexroth Ethernet 44
- Network communication 44
- CANOpen Node Slave 48
- Danfoss Inverter 55
- Frequency Converter 56
- Frequency Converter setting 56
- of process word: 57
- showed by RW register 57
- Modbus RTU Protocol: 58
- Delta Corporation 61
- DVP RS485-2 communication 62
- Controller Setting 65
- D3CellTM 71
- RS422 on the CPU unit 71
- DLoadCell 71
- EB-MOD2P-01(Bus Bridge) 72
- Emerson NetWork Power 79
- Facon Corporation 87
- Fuji SPB 91
- GE Fanuc Automation Inc 93
- HAIWELL 98
- Cable Diagram 100
- Serial Communication 100
- System configuration 100
- Communication Setting 100
- Supported Device 101
- Hitachi Inverter 101
- Hitachi IES Co., Ltd 103
- MICRO-EH 104
- Hollysys Corporation 108
- HuaDA HD-JZ06 110
- RS232 Port 112
- RS485 Port 112
- KDN Corporation 113
- Kinco Corporation 115
- Kinco ED Series 117
- Keyence Corporation 119
- Koyo Corporation 122
- PLC software setting 123
- KTC Srdlink 125
- RS232 communication 130
- RS485 communication 130
- XG5000 software setting 133
- LUST BUS Inverter 138
- Memory map 144
- Note: 1. Don’t live plug! 146
- 3Setting Your owner cable 147
- RS422 communication 148
- (support multi station) 151
- PLC Software Setting： 152
- RS485 communication 153
- modifiable 155
- Q00jCPU 159
- Q02CPU 160
- Mks controller 162
- Omron Corporation 169
- OPTO 22 179
- Register Type 181
- PMAC Motion Controller 185
- Profibus Slave 188
- PLC setting 189
- RF-IC (Card Reader) 193
- Saia-Burgess 194
- Systems Configuration 195
- Schneider Electric, Ltd 198
- PLC Setting 201
- Unitel-way protocol setting: 203
- Modbus protocol setting:： 203
- RS485communication 204
- SHIMADEN FP23 207
- SIEMENS 210
- Serial System configuration 211
- B）MPI address must be 2 215
- TMCM_303 228
- RS232 Communication Cable 230
- Trio motion controller 232
- Controller internal setting: 234
- RS485-4 communication 234
- Vigor Corporation 236
- XiLin Inverter 238
- Yamatake Corporation 240
- Yaskawa UDP 246
- 2. how to set the IP 248
- 248
- RS232 communication cable 254
- RS422 communication cable 254
- AI-7048 257
Relacionado con productos y manuales para No Siemens KDN Series
No Siemens REV23.03RF Manual de usuario
(13 paginas)
(13 paginas)
No Siemens KF Series Manual de usuario
(3 paginas)
(3 paginas)
No Siemens Life 300 BTE Manual de usuario
(28 paginas)
(28 paginas)
No Siemens eCharger Manual de usuario
(1 paginas)
(1 paginas)
No Siemens Simatic S7-300 Manual de servicio
(272 paginas)
(272 paginas)
No Siemens ARTIS 2 S Manual de servicio
(606 paginas)
(606 paginas)
No Siemens CIELO 2 P Manual de usuario
(2 paginas)
(2 paginas)
No Siemens TW 701 Series Manual de usuario
(8 paginas)
(8 paginas)
No Siemens CENTRA Manual de instrucciones
(36 paginas)
(36 paginas)
No Siemens ePen Manual de usuario
(16 paginas)
(16 paginas)
No Siemens 5TC1 series Manual de usuario
(4 paginas)
(4 paginas)
No Siemens GC..M.. Manual de usuario
(7 paginas)
(7 paginas)
No Siemens KI42F Manual de usuario
(20 paginas)
(20 paginas)
No Siemens CIELO 2 ACTIVE Manual de usuario
(2 paginas)
(2 paginas)
No Siemens GS..D.. Manual de usuario
(23 paginas)
(23 paginas)
No Siemens Pure 500 Guía de usuario
(36 paginas)
(36 paginas)
No Siemens PURE Manual de usuario
(2 paginas)
(2 paginas)
No Siemens LZ53650 Manual de usuario
(2 paginas)
(2 paginas)
No Siemens Pure SE Manual de usuario
(10 paginas)
(10 paginas)
No Siemens MC55 Manual de usuario
(3 paginas)
(3 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales