Siemens NAN 67 Series Manual de usuario descargar pdf (Pagina 39)

Appendix B: CRC-16 Calculation

02/13 Modbus® RTU Serial Communications User Manual 33

Address

(hex)

(decimal)

Parameter Name Access Notes

003C 40061 Remote/Local Set Point State R/W Bit Packed

Bit 0: 0:LSP; 1:RSP

Bit 1-15: Unused Note 12

003D 40062 Tune Set State R/W Unsigned 16 bit integer

0=Tune Set #1 1=Tune Set #2

2=Tune Set #3 3=Tune Set #4 Note 3

003E 40063 Loop Status R Bit Packed

Bit 0: Mode: 0:Manual; 1:Auto

Bit 1: Set Point: 0:SP1; 1:SP2

Bit 2: Remote/Local: 0:LSP; 1:RSP

Bit 3: Tune Set: 0:Set #1; 1:Set #2

Bit 4: LSP#3

Bit 5: LSP#4

Bit 6: CSP

Bit 7: UDC3500 set for Tune Set #1

Bit 8: UDC3500 set for Tune Set #3

Bit 9: UDC3500 set for Tune Set #4

Bit 10: Unused

Bit 11: UDC3500 Run/Hold Status

Bit 12: UDC3500 set for Any Digital Input

Active

Bit 13: UDC3500 set for Any Alarm Active

Bit 14: UDC3500 set for Cascade Operation

Bit 15: UDC3500 set for Guaranteed Soak

Deviation (Out of Limit)

Note 10, Note 12

003F 40064 Device Status R/W Bit 0: Emergency Manual

Bit 1: Failsafe

Bit 2: Working Calibration Checksum Error

Bit 3: Configuration Checksum Error

Bit 4: Factory Calibration Error

Bit 5: Hardware Failure

Bit 6:Restart After Shed

Bit 7:Configuration/ Calibration Memory

Changed

Note 13

Note 1: UDC3200, UDC3300, UDC3500 uses a prescale of 100 for this parameter.

Note 2: UDC3200, UDC3300, UDC3500 uses a prescale of 1 for this parameter.

Note 3: UDC3200, UDC3300, UDC3500 only.

Note 4:

UDC3200, UDC3300, UDC3500 Ratio and Bias are CSP parameters.

Note 5: In the UDC3200, UDC3300, or UDC3500, if the input type is configured as Carbon and the input algorithm is

configured for one of the carbon selections, the prescale value is derived from the configured decimal point.

Note 6: Not supported by UDC2300 or UDC3300

Note 7: UDC2300, UDC2500, UDC3300, UDC3200 Loop 1 Address only.

Note 8:

In the UDC3200, UDC3300, or UDC3500, if the Algorithm 1 type is configured for weighted average, RH, Summer, Sq.

Root Mult-Div, Sq Root Mult, Mult-Div, Mult, Carbon A-D, FCC, Dew Point, or Oxygen, the prescale value is derived

from the configured decimal point.

Note 9: In the UDC3300, or UDC3500 if the Algorithm 2 type is configured for weighted average, A-B/C, Sq Root Mult-Div, Sq

Root Mult, Mult-Div, Mult, or Dew Point, the prescale value is derived from the configured decimal point.

Note 10: If bits 2, 4, 5 and 6 are set, then disregard bit 1.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 75 76

Comentarios a estos manuales

Sin comentarios

Siemens NAN 67 Series Manual de usuario Pagina 39

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Siemens NAN 67 Series