Siemens Sinumerik 810T Manual de usuario descargar pdf (Pagina 88)

EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES

H 12

7018: TURN KEY SWITCH

With NC-Start the key switch was in position "setting

operation".

NC-Start is locked.

Turn the key switch in the position "automatic" to run

a program.

7020: SPECIAL OPERATION MODE ACTIVE

Special operation mode: The machine door is opened,

the auxiliary drives are switched on, the key switch is

in position "setting operation" and the consent key is

pressed.

Manual traversing the axes is possible with open

door. Swivelling the tool turret is possible with open

door. Running a CNC program is possible only with

standing spindle (DRYRUN) and SINGLE block

operation.

For safety: If the consent key is pressed for more

than 40 sec. the function of this key is interrupted, the

consent key must be released and pressed again.

7021: TOOL TURRET NOT LOCKED

The tool turret operating was interrupted.

NC start and spindle start are locked. Press the tool

turret key in the RESET status of the control.

7038: LUBRICATION SYSTEM FAULT

The pressure switch is defective or gagged.

NC-Start is locked. This alarm can be reset only by

switching off and on the machine.

Contact EMCO service.

7039: LUBRICATION SYSTEM FAULT

Not enough lubricant, the pressure switch is defective.

NC-Start is locked.

Check the lubricant and lubricate manually or contact

EMCO service.

7040: MACHINE DOOR OPEN

The main drive can not be switched on and NC-Start

can not be activated (except special operation mode)

Close the machine to run a program.

7042: INITIALIZE MACHINE DOOR

Every movement and NC-Start are locked.

Open and close the machine door to initialize the

safety circuits.

7043: PIECE COUNT REACHED

A predetermined number of program runs was

reached. NC-Start is locked. Reset the counter to

continue.

6050: M25 DURING SPINDLE ROTATION

With M25 the main spindle must stand still (consider

run-out time, evtl. program a dwell)

6055: NO PART CLAMPED

This alarm occurs when with rotating spindle the

clamping device or the tailstock reach the end position.

The workpiece has been pushed out of the chuck or

has been pushed into the chuck by the tailstock.

Check clamping device settings, clamping forces,

alter cutting data.

6056: QUILL NOT READY

Attempt to start the spindle or to move an axis or to

swivel the tool turret with undefined tailstock position.

Tailstock is locked mechanically (collision), insufficient

pressured air supply, fuse defective, magnetic switch

defective.

Check for collisions, check fuses or contact EMCO

service.

6057: M20/M21 DURING SPINDLE ROTATION

With M20/M21 the main spindle must stand still

(consider run-out time, evtl. program a dwell)

6058: M25/M26 DURING QUILL FORWARD

To actuate the clamping device in an NC program with

M25 or M26 the tailstock must be in back end position.

6064: AUTOMATIC DOOR NOT READY

Door stucks mechanically (collision), insufficient

pressured air supply, limit switch defective, fuse

defective.

Check for collisions, check fuses or contact EMCO

service.

7000: INVALID TOOL NUMBER PROGRAMMED

The tool position was programmed larger than 8.

The CNC program will be stopped.

Interrupt program with RESET and correct the pro-

gram.

7016: SWITCH ON AUXILIARY DRIVES

The auxiliary drives are off. Press the AUX ON key

for at least 0.5 sec. (to avoid accidentally switching

on) to switch on the auxiliary drives (also a lubricating

pulse will be released).

7017: REFERENCE MACHINE

Approach the reference point.

When the reference point is not active, manual

movements are possible only with key switch at

position "setting operation".

1 2 ... 83 84 85 86 87 88 89 90

Comentarios a estos manuales

Sin comentarios

Siemens Sinumerik 810T Manual de usuario Pagina 88

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Siemens Sinumerik 810T