Siemens Sinumerik 810T Manual de usuario Pagina 14
- Pagina / 90
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
EMCO WINNC SINUMERIK 810/820 T
B 2
BASICS
;;
=
;;
=
88
:
88
:
Zero Offset
With EMCO lathes the machine zero "M" lies on
the rotating axis and on the end face of the spindle
flange. This position is unsuitable as a starting
point for dimensioning. With the so-called zero
offset the coordinate system can be moved to a
suitable point in the working area of the machine.
In the setting data zero offset are four adjustable zero
offsets available.
When you define a value in the offset register, this
value will be considered with call up in program (G54
- G57) and the coordinate zero point will be shifted
from the machine zero M to the workpiece zero W.
The workpiece zero point can be shifted within a
program with "G58, G59 - programmable zero
offset" in any number.
More informations see in command description G58,
G59.
Zero offset from the machine zero point to the
workpiece zero point
Coordinate System
The X coordinate lies in the direction of the cross
slide, the Z coordinate lies in the direction of the
longitudinal slide.
Coordinate values in minus direction describe
movements of the tool system towards the workpiece,
values in plus direction away from the workpiece.
Coordinate System with Absolute
Programming
The origin of the coordinate system lies at the machine
zero "M" or at the workpiece zero "W" following a
programmed zero offset.
All target points are described from the origin of the
coordinate system by the indication of the respective
X and Z distances.
X distances are indicated as the diameter (as
dimensioned on the drawing)
Coordinate System with Incremental
Programming
The origin of the coordinate system lies at the tool
mount reference point "N" or at the cutting tip after a
tool call-up.
With incremental programming the actual pathes of
the tool (from point to point) are described.
X will be entered as radius.
Absolute coordinates relate to a fixed position,
incremental coordinates to the tool position.
The X and -X in brackets are valid for the PC
TURN 50/55 because the tool is in front of the
turning centre at this machine.
Absolute
Incremental
0:
- Software Description 1
- Contents 3
- E: @-Codes 4
- G: Survey Pages 4
- H: Alarms and Messages 4
- Starting Information 4
- A: Key Description 5
- Key functions 6
- Address and Numeric Keyboard 6
- Machine Control Keys 8
- KEY DESCRIPTION 9
- PC Keyboard 10
- Screen with Softkeys 11
- INNC SINUMERIK 810/820 T 12
- EY DESCRIPTION 12
- B: Basics 13
- Zero Offset 14
- Coordinate System 14
- Input of the 15
- Tool Data Measuring 16
- Cutter position 17
- Input of the Tool Data 18
- Tool Data Measuring with the 20
- Optical Presetting Device 20
- C: Operating Sequences 21
- Approach the Reference Point 22
- Input of the Gear Position 22
- Setting of Language and 22
- Workpiece directory 22
- Input of Programs 23
- PERATING SEQUENCES 24
- Program Administration 25
- Data Input-Output 25
- Program Run 29
- Graphic simulation 31
- D: Programming 33
- Survey of G Commands 34
- Survey of M Commands 34
- Survey of Cycles 34
- Description of G Commands 35
- G01 Linear Interpolation 35
- G02 Circular Interpolation 36
- Clockwise 36
- G03 Circular Interpolation 36
- Counterclockwise 36
- G04 Dwell 37
- G09 Exact Stop 37
- G10 - G13 Polar Coordinate 37
- Interpolation 37
- G25/G26 Programmable working 38
- G33 Thread Cutting 39
- Cutter Radius Compensation 39
- ROGRAMMING 40
- G48 Leave as Approached 42
- G50 Cancel Scale Modification 42
- G51 Scale Modification 42
- G54 - G57 Zero Offset 1 - 4 43
- G58/G59 Programmable Zero 43
- G60 Exact Stop Mode 44
- G63 Thread tapping with 44
- G70 Measuring in Inches 45
- G71 Measuring in Millimetre 45
- G92 Spindle Speed Limit 46
- G90 Absolute Programming 46
- G91Incremental Programming 46
- G94 Feed per Minute 49
- G95 Feed per Revolution 49
- G96 Constant Cutting Speed 49
- G97 Constant Spindle Speed 49
- G131 Transmit 50
- Description of Cycles 55
- L93 Cut-in Cycle 55
- L94 Undercut Cycle 56
- L97 Thread Cutting Cycle 58
- L971 Longitudinal Thread 58
- L98 Deep Hole Drilling Cycle 59
- L99 Thread Draft 60
- Contour definition 61
- Subroutines 63
- R PARAMETER 71
- OFFSET" 73
- Softkey Menu Survey 74
- Survey Guiding 76
- Control Alarms 78
- Machine Alarms 85
Relacionado con productos y manuales para Redes Siemens Sinumerik 810T
Redes Siemens RUGGEDCOM RSG2200 Manual de usuario
(24 paginas)
(24 paginas)
Redes Siemens Gigaset SE555 WLAN dsl Manual de usuario
(187 paginas)
(187 paginas)
Redes Siemens 505-2571 Especificaciones
(68 paginas)
(68 paginas)
Redes Siemens DTU3005-B Manual del operador
(141 paginas)
(141 paginas)
Redes Siemens MC35 Especificaciones
(42 paginas)
(42 paginas)
Redes Siemens SIMATIC TIWAY 1 Especificaciones
(207 paginas)
(207 paginas)
Redes Siemens RUGGEDCOM RSG2200 Especificaciones
(46 paginas)
(46 paginas)
Redes Siemens TC35 Terminal Especificaciones
(204 paginas)
(204 paginas)
Redes Siemens TC35 Terminal Especificaciones
(278 paginas)
(278 paginas)
Redes Siemens RS-485 Manual de servicio
(92 paginas)
(92 paginas)
Redes Siemens gigaset SE551 Manual de usuario
(183 paginas)
(183 paginas)
Redes Siemens SE505 Especificaciones
(135 paginas)
(135 paginas)
Redes Siemens RS-485 Manual de servicio
(46 paginas)
(46 paginas)
Redes Siemens S7-200PLC Manual de usuario
(21 paginas)
(21 paginas)
Redes Siemens DTU3005-B Manual del operador
(120 paginas)
(120 paginas)
Redes Siemens 505-2571 Manual de usuario
(30 paginas)
(30 paginas)
Redes Siemens E-110-I Manual de usuario
(10 paginas)
(10 paginas)
Redes Siemens SIMATIC TIWAY 1 Manual de usuario
(118 paginas)
(118 paginas)
Redes Siemens SL2-141 Manual de usuario
(20 paginas)
(20 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales