Siemens COM32 Guía de usuario Pagina 57
- Pagina / 126
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
© 2010 Schneider Electric. All rights reserved. Page 57
ION Setup User Guide Adding and Configuring Devices
Ethernet: Select the Gateway checkbox if the site is an Ethernet Gateway.
Refer to “Adding a new Ethernet gateway or Modbus gateway site in
ION Setup” on page 51 for more information.
Timings
Response Delay: Specify a Response Delay (in milliseconds).
Transmit Delay: Specify a Transmit Delay (in milliseconds).
Byte Timeout: Specify a Byte Timeout (in milliseconds).
RTS (Ready to Send) Control: Specify an RS232/RS485 software flow control.
Disabled: Software flow control is disabled.
Force Off: Software flow control is set to off (RS232/RS485 line held low).
Force On: Software flow control is active for the entire message string,
which holds the RS232/RS485 line high for the complete message
sequence. Use this setting for powering external devices from the RS232/
RS485 line.
Toggle: Toggles the line between receive/transmit. Use this setting for direct
connection to COM32/COM128 or similar.
Wait CTS: Waits for receipt of a Clear To Send message. Use this setting for
active flow control for reduced throughput devices (i.e. modems).
DTR (Data Terminal Ready): Specify a DTR line control.
Disabled: No software DTR line control.
Modem Ctrl: Forces the DTR line low upon “request communication end”
failure. Use this setting to force a modem disconnect.
Force Off: Sets the DTR line low. Use this setting for optical probes on IEEE
meters.
Force On: Sets the DTR line high. Use this setting for optical probes on IEC
meters.
Probe Ctrl: Use this custom setting for self-powered probes to mitigate
battery loss.
Polling
Polling Method: Specify the polling method for the selected site from the drop-
down list. Supported options are Continuous, On Demand, or Scheduled.
Edit Schedule: Edit the polling schedule for the selected site (or view the
current schedule used to poll the meters in the selected site).
- PowerLogic ION Setup 2.2 1
- Terminology 3
- Contents 5
- Chapter 1 Introduction 7
- ION Setup Features 8
- System Requirements 9
- Overview 10
- Getting More Information 11
- Installing ION Setup 12
- Communicating with Devices 13
- Connecting to serial devices 14
- Using Modem Communications 15
- Using Ethernet Communications 16
- List of Common Procedures 20
- Starting ION Setup 22
- Using the Network Viewer 26
- Left and right panes 27
- ION Setup Commands 28
- Menu Command Effect 29
- Viewing Options 31
- Viewing the unassigned group 32
- Basic versus Advanced Mode 33
- Setting Up Options 34
- Confirmation tab 35
- Security tab 35
- Conventions tab 37
- Applying Security 38
- Working in Single Device Mode 44
- Using Serial Communications 45
- Using Offline Programming 46
- Working in Network Mode 48
- Adding and Configuring Sites 49
- IP Port Description 52
- Adding a New Meter 53
- Grouping Devices 54
- Assigning a Device to a Group 55
- Editing Site Properties 55
- Editing Group Properties 58
- Editing Meter Properties 58
- Description 59
- Setup Screen Examples 62
- Example 3 63
- Example 4 63
- Overview of ION Architecture 66
- Creating new ION modules 67
- Linking ION modules 68
- ION Meter Cloning 72
- In this Chapter 73
- Setup Assistant Overview 74
- Template Screen 75
- Template Paste options 76
- Basic Setup Screen 77
- Security Screen 78
- Communications Screens 81
- 3rd Party Protocols Screen 81
- Clock Screen 83
- Demand Screen 84
- Input / Output Screens 84
- LED Pulsing Screen 85
- Energy Pulsing Screen 85
- OnBoard Digital Inputs Screen 86
- Analog Outputs Screen 86
- Memory Screen 87
- Event Log Screen 89
- EnergyDemand Log Screen 90
- Configuring Interval/Depth 91
- PT/CT Correction Screen 92
- Transformer Loss Screen 92
- Time of Use (TOU) Screen 93
- Sunday--and click OK 96
- Alarming Screen 98
- Power Quality Screen 99
- Displays Screen 99
- The Display Editor appears 100
- Verification Screen 101
- Phasor Viewer 103
- Reports Screen 104
- Writing to Multiple Registers 107
- In this chapter 109
- Displaying Data 110
- Closing data screens 111
- Performing Control Operations 112
- Chart Plotting 113
- Editing chart properties 114
- Chapter 6 Troubleshooting 117
- Troubleshooting ION Setup 118
- ION Setup Diagnostics Tools 119
- Troubleshooting Devices 122
- PowerLogic™ ION™ Setup 126
- User Guide 126
- Schneider Electric 126
Relacionado con productos y manuales para Software Siemens COM32
Software Siemens SIMATIC NET Guía de usuario
(68 paginas)
(68 paginas)
Software Siemens Simatic S7-300 Manual de usuario
(26 paginas)
(26 paginas)
Software Siemens SIMATIC NET Especificaciones
(268 paginas)
(268 paginas)
Software Siemens SIMATIC PCS 7 OSx Manual de usuario
(17 paginas)
(17 paginas)
Software Siemens v1.0 Manual de servicio
(202 paginas)
(202 paginas)
Software Siemens 270 series Instrucciones de operaciones
(274 paginas)
(274 paginas)
Software Siemens S7-400 Manual de servicio
(382 paginas)
(382 paginas)
Software Siemens AC65 Guía de usuario
(123 paginas)
(123 paginas)
Software Siemens Simatic M7-400 Manual de usuario
(266 paginas)
(266 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.121 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales