Siemens IP-Module Especificaciones Pagina 110
- Pagina / 210
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuration of connections CP143 H1 / TCP/IP manual
5-30 Rev. 00/07
Job number (ANR)
A job number{ XE "Job number" } must be allocated to each connection that should be used
by Siemens handler modules. This number is used to access the connection from the PLC
program. The job number together with the frame offset number determines the connection.
This precludes multiple assignments. The job number and the respective frame offset
number must be supplied in the control program.
Range: 1 to 199
Priority
The respective value is retrieved from the default connection. You can not alter this value
where multi-connections are concerned.
The parameter specifies the priority of the message for the CP143 H1 / TCP/IP. The priority
may range from 1 (highest priority) to 3 (lowest priority).
1 is also called the express priority, 2and3are normal priorities. Priorities 0 and 4 are not
supported. Please remember that the data transfer for the express priority 1 is no faster than
that of the normal priorities.
Range:1to3
Job type
The opposite job type is selected automatically.
The following types of job are available:
• Send transmission of unstructured data.
• Receive reception of unstructured data.
- CP143 H1 / TCP/IP 1
- About this manual 4
- Contents 5
- Rev. 00/07 i-3 7
- Lerrzeichen 10
- 1 Introduction 11
- 1-2 Rev. 00/07 12
- 1.2 General 13
- 1.3 Operation 14
- 1.4 Construction 14
- 2 Communication protocols 15
- 2.1.2 Operation 18
- 2.2 TCP/IP protocol 19
- 2-4 Rev. 00/07 20
- Rev. 00/07 2-5 21
- 2-6 Rev. 00/07 22
- 2.2.3 TCP/IP services 23
- 3 Network planning 25
- LerrzeicLerrzeichenhen 26
- 3-2 Rev. 00/07 28
- Rev. 00/07 3-3 29
- CP 143 H1 / TCP/IP 30
- Rev. 00/07 3-5 31
- 3-6 Rev. 00/07 32
- Coaxial cable 33
- 3-8 Rev. 00/07 34
- 3-10 Rev. 00/07 36
- Rev. 00/07 3-11 37
- 3-12 Rev. 00/07 38
- Rev. 00/07 3-13 39
- 3-14 Rev. 00/07 40
- Rev. 00/07 3-15 41
- 3.5 Twisted Pair 42
- Rev. 00/07 3-17 43
- 3.6 Planning a network-layout 44
- Rev. 00/07 3-19 45
- 3-20 Rev. 00/07 46
- Rev. 00/07 4-1 49
- 4-2 Rev. 00/07 50
- 4.1.2 Jumper settings 51
- 4-4 Rev. 00/07 52
- 4.1.3 Sockets and plugs 53
- 4-6 Rev. 00/07 54
- Rev. 00/07 4-7 55
- Base connector X1 56
- Base connector X2 56
- Rev. 00/07 4-9 57
- 4.2 The CP143plus firmware 58
- Dual-port-Ram (DPR) 59
- 4-12 Rev. 00/07 60
- Rev. 00/07 4-13 61
- 4.3 CP143 TCP/IP firmware 62
- Dual-port-RAM (DPR) 63
- 4-16 Rev. 00/07 64
- Rev. 00/07 4-17 65
- 4-18 Rev. 00/07 66
- Rev. 00/07 4-19 67
- 4-20 Rev. 00/07 68
- Rev. 00/07 4-21 69
- 4-22 Rev. 00/07 70
- Rev. 00/07 4-23 71
- 4-24 Rev. 00/07 72
- Rev. 00/07 4-25 73
- 4-26 Rev. 00/07 74
- Rev. 00/07 4-27 75
- Indicators for SEND 76
- Indicators for RECEIVE 76
- Rev. 00/07 4-29 77
- 4-30 Rev. 00/07 78
- 5 Software 79
- 5-2 Rev. 00/07 82
- Rev. 00/07 5-3 83
- 5-4 Rev. 00/07 84
- 5.4 Using on-line help 85
- 5.5 The base file 86
- 5.5.2 Printing the base file 87
- 5-8 Rev. 00/07 88
- Rev. 00/07 5-9 89
- 5-10 Rev. 00/07 90
- Rev. 00/07 5-11 91
- 5-12 Rev. 00/07 92
- 5.6 Initialization 93
- 5-14 Rev. 00/07 94
- 5.6.2 Online 95
- 5.6.3 System configuration 96
- 5.7 Real-time clock functions 97
- 5-18 Rev. 00/07 98
- Rev. 00/07 5-19 99
- 5-20 Rev. 00/07 100
- Rev. 00/07 5-21 101
- 5-22 Rev. 00/07 102
- Rev. 00/07 5-23 103
- 5-24 Rev. 00/07 104
- Rev. 00/07 5-25 105
- 5-26 Rev. 00/07 106
- 5.8.3 Indirect addressing 107
- 5-28 Rev. 00/07 108
- 5.8.4 Multi-connections 109
- 5-30 Rev. 00/07 110
- 5.8.5 List of connections 111
- number determines 112
- Range: 1 to 199 112
- 5.9 General test functions 113
- 5.9.2 Anzw Dump 114
- Rev. 00/07 5-35 115
- 5-36 Rev. 00/07 116
- Rev. 00/07 5-37 117
- 5-38 Rev. 00/07 118
- Rev. 00/07 5-39 119
- 5-40 Rev. 00/07 120
- Rev. 00/07 5-41 121
- 5.10.1 Initialization 122
- Rev. 00/07 5-43 123
- 5-44 Rev. 00/07 124
- Rev. 00/07 5-45 125
- 5-46 Rev. 00/07 126
- Rev. 00/07 5-47 127
- 5-48 Rev. 00/07 128
- Rev. 00/07 5-49 129
- be supplied in the 130
- Rev. 00/07 5-51 131
- 5.10.3 Test functions 132
- 5.11.1 Initialization 133
- 5-54 Rev. 00/07 134
- Rev. 00/07 5-55 135
- 5-56 Rev. 00/07 136
- Rev. 00/07 5-57 137
- Rev. 00/07 5-59 139
- 5-60 Rev. 00/07 140
- Rev. 00/07 5-61 141
- 5-62 Rev. 00/07 142
- number must be 143
- 5-64 Rev. 00/07 144
- 5.11.3 Test functions 145
- 5-66 Rev. 00/07 146
- Rev. 00/07 5-67 147
- 5-68 Rev. 00/07 148
- Rev. 00/07 5-69 149
- 5-70 Rev. 00/07 150
- Rev. 00/07 5-71 151
- 5-72 Rev. 00/07 152
- Rev. 00/07 5-73 153
- 5-74 Rev. 00/07 154
- Rev. 00/07 5-75 155
- 5-76 Rev. 00/07 156
- H1 / TCP/IP manual Software 157
- WRITE job FETCH job 157
- H1 / TCP/IP manual 158
- 6 Commissioning 159
- LerrzLerrzeicheneichen 160
- Rev. 00/07 6-3 163
- Q 304/314 interface 165
- 6.2 Start-up properties 167
- 6.2.2 Status indicators 168
- 6.3 PLC programming 169
- 6.3.2 Programming 170
- 6.4 Example 171
- 6.4.2 Problem 172
- Rev. 00/07 6-13 173
- 6.4.3 Programs for the PLCs 174
- Rev. 00/07 6-15 175
- 6-16 Rev. 00/07 176
- Rev. 00/07 6-17 177
- 6-18 Rev. 00/07 178
- Rev. 00/07 6-19 179
- 6-20 Rev. 00/07 180
- Rev. 00/07 6-21 181
- Station 1 182
- Station 2 182
- Rev. 00/07 6-23 183
- 6-24 Rev. 00/07 184
- Rev. 00/07 6-25 185
- 6-26 Rev. 00/07 186
- 6-28 Rev. 00/07 188
- Rev. 00/07 6-29 189
- 6-30 Rev. 00/07 190
- Rev. 00/07 6-31 191
- 6-32 Rev. 00/07 192
- Appendix 193
- A-2 Rev. 00/07 196
- Rev. 00/07 B-1 197
- B-2 Rev. 00/07 198
- Rev. 00/07 B-3 199
- B-4 Rev. 00/07 200
- Rev. 00/07 C-1 201
- C-2 Rev. 00/07 202
- Rev. 00/07 D-1 203
- D-2 Rev. 00/07 204
- Rev. 00/07 E-1 205
- E-2 Rev. 00/07 206
- Rev. 00/0 F-1 207
- F-2 Rev. 00/07 208
- Rev. 00/0 F-3 209
- F-4 Rev. 00/07 210
Relacionado con productos y manuales para Detectores de humo Siemens IP-Module
(57 paginas)
Detectores de humo Siemens BH17 7ER Especificaciones
(83 paginas)
(83 paginas)
Detectores de humo Siemens IP-Module Manual
(360 paginas)
(360 paginas)
Detectores de humo Siemens BH17 7ER Especificaciones
(120 paginas)
(120 paginas)
Detectores de humo Siemens FS-250 Manual de usuario
(20 paginas)
(20 paginas)
Detectores de humo Siemens FS-250 Especificaciones
(14 paginas)
(14 paginas)
Detectores de humo Siemens FS-250 Especificaciones
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales