Siemens CU240S DP Instrucciones de operaciones descargar pdf (Pagina 218)

Appendix

A.5 Acceptance Log

Control Units CU240S

218 Operating Instructions, 10/2007, A5E00766042B AC

Table A-6 Description of the fail-safe equipment/devices

Drive No. Example:

Wiring of the STO terminals (protective door, EMERGENCY STOP), grouping

of the STO terminals, etc.

1 2 ... 213 214 215 216 217 218 219 220 221 222 223 ... 233 234

SINAMICS 1
Table of contents 5
Table of contents 7
Introduction 10
Safety notes 11
General 12
Transport and storage 13
Operation 14
Dismantling and disposal 14
Common features 17
Commissioning functions 17
Operating functions 18
Control functions 18
Protective functions 18
Description 19
3RZHU0RGXOH 20
Terminals 23
Option port 25
Installing/Mounting 29
24 V power supply 30
Control settings 33
&8 34
Installing/Mounting 37
Maximum cable length 38
Cable installation rules 39
Connectors 39
Removing a bus connector 40
Screening 41
Equipotential bonding 42
4.6 Installation Check List 45
4.6 Installation Check List 48
5.1 Single Commissioning 49
5.2 Series Commissioning 50
5.2 Series Commissioning 51
Upload of parameter sets 52
Download of parameter sets 52
Manual download 53
Automatic download 54
5.4 Message F00395 56
Commissioning overview 60
Single commissioning 60
Series commissioning 60
5.5.3 Basic Commissioning 61
Vector Control mode 63
Parameter settings 65
General settings 68
Pulse Encoder 69
Temperature Sensor 69
Selection of command source 70
Assigning digital inputs 71
Assigning digital outputs 72
Frequency setpoint set 72
Analog outputs 75
JOG frequency 76
Additional Setpoints 76
6NLSIUHTXHQF\ 77
Reset to the factory setting 79
5.5.5.3 Checksums 84
Change password 85
Enabling fail-safe functions 85
Test stop interval setting 87
Safe Stop 1 setting 88
Safely-limited Speed 89
Acceptance test 91
Interfaces STARTER 95
STARTER projects 96
6,1$0,&6 99
Prerequisites 100
Procedure 100
Automatic Download 102
Automatic download fault 103
Description 104
Commissioning 105
3[8PLQ 106
Commissioning 108
5.8.2 Encoder Fault Codes 109
5.9 Parameters 110
5.9.2 Monitoring parameters 111
5.9.3 Parameter Attributes 111
Access level 112
Can be changed 113
Data types 113
Grouping 114
Quick commissioning 115
Value range 115
Data sets 115
Overview 116
Successful swap 119
Swap fault 120
Rules regarding a swap 120
CU Swap 121
PM Swap 121
Communication 123
Parameter channel 124
Parameter identifier (PKE), 1 125
6.1 PROFIdrive Profile V4.1 126
Parameter index (IND) 2 127
Parameter value (PWE) 3 129
6.2 Cyclic Communication 130
Communication 131
6.2 Cyclic Communication 131
6.2 Cyclic Communication 136
Control word 1 (STW1) 137
An example 139
Status word 1 (ZSW1) 140
Status word 2 (ZSW2) 141
6.3 Acyclic Communication 142
6.3.1 Parameter Channel 143
6.3 Acyclic Communication 144
6.3 Acyclic Communication 145
General information 149
Technical data 149
PROFIBUS DP parameters 151
Installing a G120 GSD file 155
Failsafe inverters 156
6.4.3.1 Read Parameters 159
Requirements 159
Task description 159
(SFC 59) and WR_REC (SFC 58) 163
6.4.3.2 Write Parameters 164
WR_REC (SFC 58) 165
PROFINET 166
6.5.2 Addresses 167
IP address assignment 168
Sub-network mask 168
Default Gateway 168
Module ID 169
Device name 169
Device-ID 169
Default router 170
PROFINET parameters 170
See also 175
6.5.4.1 Read Parameters 176
Read/write request 176
2))21 178
6.6 Communication via USS 179
Connector 180
6WDUW'HOD\ 866IUDPH 181
Mirror Broadcast 182
5 address bits 182
Basic USS parameters 183
Use data structure 183
6.6.5 USS Parameter Channel 184
6WDUW'HOD\ 185
0DVWHU5HTXHVW 0DVWHU5HTXHVW 185
6ODYH5HVSRQVH 185
6.6 Communication via USS 186
Process Timeouts 187
Other errors 187
7.1 ON/OFF Commands 190
Sources for ON/OFF command 191
ON/OFF via DI/DO 191
ON/OFF via BOP 191
7.2.1 LED Display 192
Behavior of the status LED 193
CU states displayed via LED 194
Operation 195
Troubleshooting 197
Alarms 198
Display 198
8.2 Diagnostics Display 199
Troubleshooting 201
Standard diagnostics 202
Service and maintenance 205
China (Beijing) 206
Online Service and support 206
Contact address 206
Regional contacts 206
Spare parts/Accessories 209
11.2 PC Connection Kit 210
Appendix 211
First Environment 212
Second Environment 212
Category C1 212
Category C2 212
A.3 EMC Overall Performance 213
EMC Immunity 214
A.4 Standards ((PM240)) 215
A.5 Acceptance Log 216
Appendix 217
A.5 Acceptance Log 217
A.5 Acceptance Log 218
Executing the test 219
Checksums 222
Data back-up/archiving 223
Signatures 223
List of abbreviations 225
B.1 Abbreviations 226
List of abbreviations 227
B.1 Abbreviations 227
Control Units CU240S 231
Control Units CU240S 232

Comentarios a estos manuales

Sin comentarios

Siemens CU240S DP Instrucciones de operaciones Pagina 218

Comentarios a estos manuales