Siemens DTU3005-B Manual del operador descargar pdf (Pagina 62)

Appendix A: Supported PLCs

58 Siemens Energy & Automation, Inc.

ASupported PLCs

Application Notes

A.1 Allen-Bradley PLC 5, SLC500 and

MicroLogix PLCs

Registers Accessed

The DTU3005 will only access registers in integer files

in the PLC memory (N file types). When specifying

file number is entered into the File field, and the ele-

ment number within the file is entered into the Regis-

ter field. Initial register number is 0.

Protocols Supported

The DTU3005 uses the DF1 protocol, which is also

known as Full Duplex or Point-to-Point. It supports

both the CRC and BCC methods of error checking.

Please note that the MicroLogix PLC only supports the

CRC method of error checking. Therefore, when using

a MicroLogix PLC, the protocol selected on the port

configuration screen in the DTU3005 Editor software

must be “AB SLC500 (CRC)”.

A.2 GE Fanuc 90/20, 90/30 and 90/70

PLCs

Registers Accessed

The DTU3005 will only access registers in the Data

entering register numbers, only the offset into this

area (1-9999) should be entered. For example, to

access register number %R1, the value 1 should be

entered. To access register number %R9999, the value

9999 should be entered.

A.3 Idec Micro-3 PLCs

Registers Accessed

The DTU3005 will only access registers in the Data

entering register numbers, only the offset into this

area (0-9999) should be entered. For example, to

access register number D1, the value 1 should be

entered. To access register number D9999, the value

9999 should be entered.

Link Adapter Requirement

The DTU3005 requires an Idec Link Adapter or equiva-

lent to be used when communicating with any of the

FA Series PLCs.

A.4 Idec FA Series PLCs and Square D

Model 50

Registers Accessed

The DTU3005 will only access registers in the Data

entering register numbers, only the offset into this

area (0-9999) should be entered. For example, to

access register number D1, the value 1 should be

entered. To access register number D9999, the value

9999 should be entered.

Link Adapter Requirement

The DTU3005 requires an Idec Link Adapter or equiva-

lent to be used when communicating with any of the

FA Series PLCs.

A.5 Koyo/PLC Direct 205 Series PLCs

Registers Accessed

The DTU3005 can access all register types in the 205

Series PLC through the use of the V-Memory assign-

ments shown in the following table:

Table A.1 Supported PLCs and Protocols

App.

No.

Manufacturer Model Protocol

A.1 Allen-Bradley PLC-5 4

SLC 503,

SLC 50

Micrologix

DF1 Full-Duplex

A.2 GE Fanuc 90/20,

90/30,

90/70,

Micro

SNP

A.3

A.4

Idec FA Series

Micro-3

1:1 Computer Link

Computer Link

A.5

A.6

A.7

Koyo 205,

305,

405 Series

DirectNet (Link Port)

K-Sequence (Prog

Port)

A.8 Mitsubishi FX,

FXo,

FXon

Monitor Interface

A.9 Modicon All models Modbus RTU or

ASCII

A.10 Omron C Series,

CQM Series

Host-Link

A.11 Siemens S7-200 Point-to-Point (PPI)

A.14 Siemens/TI 500 Series ASCII Data Link

A.4

A.12

A.13

Square D Model 50

Models 100-700

TSX07

1:1 Computer Link

SY/MAX (Prog Port)

Uni-Telway

A.15

A.16

Toshiba EX, M Series,

T Series

Computer-Link

Binary

Computer-Link

ASCII

A.17 Westinghouse PC-1100 Programming Port

Table A.2 Koyo/PLC Direct 205 Registers

V-Memory Address PLC Registers Accessed

V00000 – V00177 Timer T0 – T177 Current Values

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 140 141

Comentarios a estos manuales

Sin comentarios

Siemens DTU3005-B Manual del operador Pagina 62

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Siemens DTU3005-B