Siemens v1.0 Manual de servicio Pagina 85
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Simple example
2.7 Testing HMI screen
STEP 7 Basic V10.5
Getting Started, 12/2009, A5E02651459-01
85
2.7 Testing HMI screen
2.7.1 Load HMI screen to the HMI device
Introduction
You can load the Getting Started project to an HMI device and execute it in runtime. To do
this, you must have a connection between the configuration device and the HMI device. If
you are not using an HMI device, you can simulate the runtime in the TIA Portal (see
Simulate runtime (Page 87)).
Runtime in HMI device
HMI devices are used to operate and monitor tasks in process and production automation.
If you are using an HMI device for the Getting Started project, make sure that a connection
has been established between the HMI device and the PLC.
Because the HMI screen of the Getting Started project mainly uses PLC tags, the animations
of the objects will only be executed if a connection is established between the HMI device
and the PLC.
Requirements
● A connection has been established with the HMI device.
● The HMI device is configured correctly.
● The HMI device is in transfer mode.
- SIMATIC 1
- TIA Portal 1
- STEP 7 Basic V10.5 1
- Legal information 2
- Table of contents 3
- 1.1 Overview 6
- 1.2 TIA Portal basics 7
- 7,$3RUWDO 8
- 8QLIRUPHQJLQHHULQJV\VWHP 8
- :LQ&&%DVLF9 8
- 67(3%DVLF9 8
- 1.2.3 Data management 9
- Library concept 10
- 1.3 Views in the TIA portal 11
- 1.3.2 Portal view 12
- 1.3.3 Project view 13
- TIA Portal Introduction 14
- 1.3 Views in the TIA portal 14
- 1.4 Example projects 15
- 1.4 Example projects 16
- 1.4.2 Loading a project 17
- TIA Portal Introduction 19
- 1.4 Example projects 19
- Simple example 21
- 2.3.1 Inserting a PLC 23
- Simple example 25
- Network view 26
- Device view 28
- 2.3.3 Configure PLC 29
- 2.4 Create program 31
- 2.4 Create program 33
- 2.4 Create program 34
- 2.4.4 What are networks? 35
- LAD instructions 36
- Normally open contact 37
- Negated coil 38
- 2.4.6 What are tags? 42
- PLC tag table 44
- 2.5 Test program 48
- 2.5 Test program 50
- 2.5 Test program 51
- Additional information 53
- +0, 3/& 3URFHVV 57
- Adding a new HMI device 58
- 2.6 Create HMI screen 59
- 2.6 Create HMI screen 60
- Graphic objects 65
- Use of graphic objects 65
- External HMI tags 66
- Internal HMI tags 77
- 2.7 Testing HMI screen 85
- 2.7.2 Simulate runtime 87
- 2.7 Testing HMI screen 88
- 3.1 Introduction 90
- 3.2 Expanding the program 91
- Normally closed contact 97
- Extended example 100
- 3.2 Expanding the program 100
- 2SHUDQG! 101
- Procedure 102
- Requirements 103
- Introduction 103
- Extended example 105
- 3.2 Expanding the program 105
- On delay 110
- Output coil 110
- 3.4 Expand HMI screen 123
- 3.4 Expand HMI screen 124
- 3.4 Expand HMI screen 129
- 3.5 Simulate HMI screen 132
- Testing in the HMI device 133
- 3.5 Simulate HMI screen 134
- 4.1 Introduction 135
- Use of the PID controller 136
- 4.1 Introduction 137
- STEP 7 Basic V10.5 140
- 4.4 Load simulation block 143
- 4.4 Load simulation block 144
- 4.4 Load simulation block 145
- 4.5 Configure PID controller 150
- Block name 151
- Parameter 151
- 4.8 Adjust HMI screen 158
- 4.8 Adjust HMI screen 159
- 4.8 Adjust HMI screen 160
- Controller optimization 161
- Example "Motion" 165
- Hardware configuration 166
- Example "Motion" 167
- 5.1 Introduction 167
- 5.4 Enable axis 173
- 5.4 Enable axis 174
- 5.4 Enable axis 175
- 5.5 Position axis relative 176
- 5.5 Position axis relative 177
- 5.5 Position axis relative 178
- 5.6 Expand HMI screen 180
- 5.6 Expand HMI screen 181
- 5.6 Expand HMI screen 184
- 5.7 Simulate HMI screen 189
- 5.7 Simulate HMI screen 190
- 5.8 Start diagnostics view 191
- 5.8 Start diagnostics view 192
- 5.8 Start diagnostics view 193
- Glossary 197
- Glossary 199
Relacionado con productos y manuales para Software Siemens v1.0
Software Siemens 270 series Instrucciones de operaciones
(274 paginas)
(274 paginas)
Software Siemens S7-400 Manual de servicio
(382 paginas)
(382 paginas)
Software Siemens AC65 Guía de usuario
(123 paginas)
(123 paginas)
Software Siemens Simatic M7-400 Manual de usuario
(266 paginas)
(266 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.148 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales