Siemens FIREFINDER-XLS Manual de inicio rápido descargar pdf (Pagina 11)

DESCRIPTION 1-7

CHAPTER 1 | FIREFINDER-XLS INSTALLATION, OPERATION AND MAINTENANCE MANUAL

HNET

XNET FAIL

XNET

STYLE 7

ENABLED

CAN

ACTIVE NETWORKS

HNET/XNET STYLE

GROUND FAULT

NETWORK

PORT

LOOP B FAIL

GND FAULT

LOOP AFAIL

STYLE 4

DISABLED

HNET

CARD FAIL

HNET FAIL

CAN FAIL

RESET

POWER

NIC-C

CSB CAN Sounder Board The CSB is a module that contains a sounder (buzzer) that

can be used with the SCM-8 or FCM-6 to provide audible

feedback to indicate that a switch closed properly and

communication was successful. The CSB requires no

programming.

FCM-6 Control Module The FCM-6 contains six sets of three pushbutton switches and

their corresponding LEDs. The ON and AUTO switches both

have one bi-color (red/green) LED while the OFF switch has

one bi-color and one yellow LED. The functions of the switches

and LEDs are programmed using the Zeus Tool (Refer to the

Zeus Quick Start Guide, P/N 315-033875). All LEDs can be

programmed ON, OFF, or FLASHING.

HLIM Loop Isolator Module The HLIM Loop Isolator Module isolates short circuits on

FireFinder-XLS intelligent loops. By placing devices between

HLIMs during installation, a short in the wiring within that group

is disconnected from the rest of the loop. The remainder of the

devices continue to operate. The HLIM operates in both Style 6

(Class A) and Style 4 (Class B) circuits.

LCM-8 LED Control Module The LCM-8 contains eight pairs of LEDs. Each pair contains one

bi-color (red/green) and one yellow LED. The functions of the

LEDs are programmed using the Zeus Tool (Refer to the Zeus

Quick Start Guide, P/N 315-033875). All LEDs can be pro-

grammed ON, OFF, or FLASHING. These LEDs are used for fire

system status annunciation.

NIC-C Network Interface The NIC-C is a card that provides HNET or XNET and CAN network commu-

Card nication. The HNET/XNET network can be wired either Style 4 or Style 7. For

HNET one NIC-C is required in each enclosure. For XNET one NIC-C is

required per system. This NIC-C must be installed in the same enxlosure as

the PMI. Each NIC-C occupies one HNET address.

The CAN network can be isolated within a given enclosure or extended

external to the enclosure. External CAN networks require either an RNI,

OCM-16 or SIM-16 in the remote enclosure. The CAN address of the NIC-C

does not need to be set.

The NIC-C supervises the network to insure proper operation. Any faults that

are detected by the NIC-C are reported to the PMI for annunciation. In addition, the

NIC-C has diagnostic LEDs that indicate which faults have been found. Individual

LEDs are included for Loop A and Loop B faults, as well as an LED for complete

failure of the network. The NIC-C can also be configured to perform ground fault

detection on the network.

TRBL

TRBL TRBL

Buzzer

IN - LINE 1

IN - LINE 2

OUT - LINE 1

OUT - LINE 2

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 71 72

Comentarios a estos manuales

Sin comentarios

Siemens FIREFINDER-XLS Manual de inicio rápido Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Siemens FIREFINDER-XLS