Siemens SPARC M8000 Guía de usuario

SPARC® EnterpriseM8000/M9000 ServersProduct NotesFor XCP version 1060Order No. U41758-J-Z816-2-76Part No. 820-3792-11February 2008, Revision A

2 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Japanese Site:http://primeserver.fujitsu.com/sparcenterprise/

SPARC Enterprise M8000/M9000 Servers Product Notes 3Note – See “Software Resources” on page vii for information on how to find the latest patches. I

4 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Known IssuesThis section describes known issues in this relea

SPARC Enterprise M8000/M9000 Servers Product Notes 5 To complete updating the OpenBoot PROM firmware in the target domain, be sure to power off/on

6 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Hardware Installation and Service IssuesThis section describe

SPARC Enterprise M8000/M9000 Servers Product Notes 7Hardware Documentation UpdatesTABLE 2 lists known documentation updates.TABLE 2 Documentation U

8 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Updates of the SPARC Enterprise M8000/M9000 Servers Site Plan

SPARC Enterprise M8000/M9000 Servers Product Notes 9FIGURE1-18 SPARC Enterprise M9000 Server (Base Cabinet) + Power Cabinet Bottom ViewUnit: mm (i

10 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Software IssuesThis section describes software specific issu

SPARC Enterprise M8000/M9000 Servers Product Notes 11RTIF1-070824-004On the XSCF Web, on the Domain Status screen, when you select an XSB displayed

PleaseRecycleCopyright 2007-2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. and FUJITSU LIMITED, 1-1, Kamikoda

12 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008RTIF1-070904-006While executing the domain power-on, domain

SPARC Enterprise M8000/M9000 Servers Product Notes 13RTIF1-071116-001After using the addfru(8) or replacefru(8) command to hotplug a CMU, further DR

14 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008RTIF1-071129-003An error log cannot be registered in XSCF

SPARC Enterprise M8000/M9000 Servers Product Notes 15Solaris Issues and WorkaroundsTABLE 4 lists known issues and possible workarounds.TABLE 4 Spec

16 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 20086449315 The Solaris cfgadm(1M) command does not unconfigure

SPARC Enterprise M8000/M9000 Servers Product Notes 176485555 On the SPARC Enterprise M8000/M9000 servers, On-board Gigabit Ethernet NVRAM corruption

18 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 20086502204 Unexpected error messages may be displayed on consol

SPARC Enterprise M8000/M9000 Servers Product Notes 196511374 Unexpected error messages may be displayed on console after changing the system configu

20 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 20086522017 DR and ZFS may not be used in the same domain.Reduce

SPARC Enterprise M8000/M9000 Servers Product Notes 216532215 volfs or dscp service may fail when domain is booted.svc:/platform/sun4u/dscp:default:

Copyright 2007-2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. et FUJITSU LIMITED, 1-1, Kamikodanaka 4-chome,

22 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 20086539084 There is a low probability of a domain panic during

SPARC Enterprise M8000/M9000 Servers Product Notes 236551356 The system panics when running hotplug (cfgadm(1M)) to configure a previously unconfigu

24 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 20086564934 Performing a DR deleteboard(8) operation on a board

SPARC Enterprise M8000/M9000 Servers Product Notes 256589546 prtdiag(8) command does not show all I/O devices of the following cards:• SG-XPCIE2FC-

26 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Identifying Permanent Memory in a Target Board 1. Log in to

SPARC Enterprise M8000/M9000 Servers Product Notes 27Upgrading From XCP104x to XCP 1050 or Later The following steps describe the case of upgrading

28 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 20086. Collect an XSCF snapshot to archive system status prior t

SPARC Enterprise M8000/M9000 Servers Product Notes 2913. Wait until XSCF firmware reaches the ready state.This can be confirmed when the READY LEDs

30 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 200819. Confirm that both the current and reserve banks of XSCFU

SPARC Enterprise M8000/M9000 Servers Product Notes 31b. Confirm switching over between XSCFs using the following commands:Confirm XSCF#1 is standby,

32 SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Software Documentation UpdatesThis section contains late-bre

v ContentsPreface viiTechnical Support viiSoftware Resources viiAccessing Documentation viiiFujitsu Siemens Computers Welcomes Your Comments viiiSPARC

vi SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008 Software Issues 10XCP Issues and Workarounds 10Solaris Issu

viiPrefaceThese product notes contain late-breaking information about the SPARC® Enterprise M8000/M9000 server hardware, software, or documentation th

viii SPARC Enterprise M8000/M9000 Servers Product Notes for XCP Version 1060 • February 2008Accessing DocumentationInstructions for installing, admini

1SPARC Enterprise M8000/M9000 Servers Product NotesThese product notes contain late-breaking information about the SPARC® Enterprise M8000/M9000 ser