Siemens SIMATIC TIWAY 1 Especificaciones Pagina 61
- Pagina / 207
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Communication
Settings
4–4
Communication Settings
There are two banks of switches located on the rear of the DCM that are used to set
the communications parameters.
Baud 1 2 3
300 ON OFF OFF
600 OFF ON OFF
1200 ON ON OFF
2400 OFF OFF ON
4800 ON OFF ON
9600 OFF ON ON
19200 ON ON ON
38400 OFF OFF OFF
Baud Rate
ODD Parity
Switch Positions
Self Test
NO Parity
Set to OFF
Time* 6 7 8
0 OFF OFF OFF
2 ON OFF OFF
5 OFF ON OFF
10 ON ON OFF
20 OFF OFF ON
50 ON OFF ON
100 OFF ON ON
500 ON ON ON
*Delay time in milliseconds
Switch Positions
OFF ON
SW 4
SW 5
Station
Type
Station Type 1 2
DirectNET Slave OFF OFF
DirectNET Master OFF ON
DirectNET Peer ON OFF
Modbus) RTU Slave ON ON
COM Timeout Disable
ASCII Mode
COM Timeout Enable
Hexadecimal Mode
1
2
3
4
5
6
7
8
1
2
3
4
Switch Positions
Delay Time
Baud Rate: Positions 1 – 3 on SW4 are used to set the baud rate for the DCM. There
are eight baud rate selections available from 300 baud to 38.4K baud.
Parity: Position 4 on SW4 selects between the two parity options, odd or none.
Self-Test: Position 5 on SW4 selects the factory self-test and should always be
switched off. If the self-test is on, the module will not operate correctly.
Response Delay Time: Positions 6 – 8 on SW4 set the response delay time. This is
primarily used when you’re using modems and determines how long the DCM will
wait before it responds to a communication request. If you’re using all
DirectLOGIC equipment, a response delay is not required and you should set the
time to 0. If you’re using a modem, check the documentation to determine the proper
delay time.
Station Type: Positions 1 and 2 on SW5 select the DCM protocol and the station
type, master or slave. The DCM is very versatile and can actually support a second
protocol ModbusR. Be sure you have selected the proper protocol for your network,
either DirectNET or ModbusR.
Host as Master: If you’re using a host as master, set the DCM as a DirectNET slave.
PLC as Master: If the DCM is in a master station, then set the DCM as a DirectNET
master. If the DCM is in a slave station, then set the DCM as a DirectNET slave.
Peer as Master: If you’re using a peer network, set both stations as DirectNET
peers.
Communication Timeout: Position 3 on SW5 selects the communication timeout.
Don’t disable the timeout for normal use. Communication Timeout Disable is
normally used only if you’re developing your own DirectNET programs. By disabling
the timeout, you can send one DirectNET component without any communication
problems. If you have this timeout disabled and a communication error does occur,
you must restart communications by sending a retry or an End of Transmission
(EOT) command.
ASCII / HEX Mode: Position 4 on SW5 selects between ASCII and HEX modes of
data representation. Set the switch to match your network parameters.
DL405 DCM
Communication
Switches
DCM Rear View
- DirectNETt 1
- Trademarks 2
- Manual Revisions 3
- Table of Contents 4
- How to Use 13
- Introduction 14
- Getting Started with 16
- DirectNET 16
- Communications 16
- The DirectNET Basics 17
- Operator Interface 20
- Choosing a Configuration 23
- Combination 24
- 1 – PLC as Master Network 24
- 2 – Host as Master Network 24
- 3 – Peer as Master Network 24
- How can I create a network? 27
- Network Design 28
- Choosing the Configuration 29
- Possible Configurations 31
- Step 3: Secure the shield to 37
- DL430 and DL440 Port Pinouts 39
- DL405 DCM Port Pinouts 40
- DL340 CPU Port Pinouts 41
- DL305 DCU Port Pinouts 42
- DL240 CPU Port Pinouts 43
- Point-to-point Cables 44
- Master Slave 47
- Multi-Drop Cables 49
- Network Design Checklist 57
- Communication 58
- Settings 58
- 10 11 12 13 14 15 62
- D3–340 CPU 67
- Port On Delay Off Delay 68
- Port 1 R776 R777 68
- Port 2 R774 R775 68
- Programs 72
- Y20 – Y37 73
- Y0 – Y17 73
- * See Note on DCM Address 75
- Specifying the Amount of Data 76
- 01234567 79
- DirectNET Host 82
- Modes of Operation 85
- Protocol Components 87
- Initiating the Request 91
- Acknowledging the Request 92
- Defining the Request 93
- Transferring Data 95
- ETB or ETX 96
- Data Block 96
- Calculating the Data LRC 98
- Ending the Request 99
- Timing Considerations 100
- Network Operation 103
- Starting the Network 104
- Troubleshooting 105
- & Troubleshooting 107
- Master / Slave 110
- The Example 111
- Remember these Four Steps! 113
- Step 1: Design the Network 114
- *Delay time in milliseconds 116
- Step 4: Start the Network 124
- V MON 0000 XXXX 126
- Peer Master Example 128
- Host Master Example 144
- Appendix C 154
- Host Master 154
- Data Types and 159
- Memory Maps 159
- DL405 Data Types 160
- DL430 Memory Map 165
- DL440 Memory Map 166
- X Input Bit Map 167
- Y Output Bit Map 168
- Remote I/O Bit Map 169
- Control Relay Bit Map 171
- Appendix D 174
- DL405 Memory Map 174
- Timer Status Bit Map 175
- Counter Status Bit Map 176
- Memory Map 177
- DL305 Data Types 178
- DL330 Memory Map 181
- DL330P Memory Map 182
- DL340 Memory Map 183
- I/O Point Bit Map 184
- Special Relays 187
- 0 10010011 0100010 188
- R565 R564 188
- Data Registers 189
- Shift Register Bit Map 192
- Special Registers 193
- DL305 / 405 Cross Reference 194
- DL205 Data Types 197
- DL230 Memory Map 202
- DL240 Memory Map 203
Relacionado con productos y manuales para Redes Siemens SIMATIC TIWAY 1
Redes Siemens RUGGEDCOM RSG2200 Especificaciones
(46 paginas)
(46 paginas)
Redes Siemens TC35 Terminal Especificaciones
(204 paginas)
(204 paginas)
Redes Siemens TC35 Terminal Especificaciones
(278 paginas)
(278 paginas)
Redes Siemens RS-485 Manual de servicio
(92 paginas)
(92 paginas)
Redes Siemens gigaset SE551 Manual de usuario
(183 paginas)
(183 paginas)
Redes Siemens SE505 Especificaciones
(135 paginas)
(135 paginas)
Redes Siemens RS-485 Manual de servicio
(46 paginas)
(46 paginas)
Redes Siemens S7-200PLC Manual de usuario
(21 paginas)
(21 paginas)
Redes Siemens DTU3005-B Manual del operador
(120 paginas)
(120 paginas)
Redes Siemens 505-2571 Manual de usuario
(30 paginas)
(30 paginas)
Redes Siemens E-110-I Manual de usuario
(10 paginas)
(10 paginas)
Redes Siemens SIMATIC TIWAY 1 Manual de usuario
(118 paginas)
(118 paginas)
Redes Siemens SL2-141 Manual de usuario
(20 paginas)
(20 paginas)
Redes Siemens SE505 Manual de usuario
(132 paginas)
(132 paginas)
Redes Siemens SPC3 Especificaciones
(38 paginas)
(38 paginas)
Redes Siemens E-110-I Manual de usuario
(111 paginas)
(111 paginas)
Redes Siemens Gigaset SX761 dsl Especificaciones
(118 paginas)
(118 paginas)
Redes Siemens Sinumerik 810T Manual de instrucciones
(62 paginas)
(62 paginas)
(142 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.792 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales