Siemens SIPART PS2 6DR51xx Instrucciones de operaciones Pagina 168
- Pagina / 244
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Parameterizing/addressing
10.4 Description of parameters
SIPART PS2 with and without HART communications
170 Operating Instructions, 09/2008, A5E00074631-08
The factory setting is "OFF".
G1.LEVL1 - threshold 1
Use this sub-parameter to set a threshold in percent. Use threshold 1 to monitor the upper
hard end stop. Set the threshold in a range from "0.1" to "10.0".
The positioner triggers a fault message if the difference between the upper hard end stop
and the initialization value exceeds threshold 1. The process to activate and display this fault
message is described in the "XDIAG" parameter.
The factory setting is "1.0".
G2.LEVL2 - threshold 2
Use this sub-parameter to set a threshold in percent. Use threshold 2 to monitor the upper
hard end stop. Set the threshold in a range from "0.1" to "10.0".
The positioner triggers a fault message if the difference between the upper hard end stop
and the initialization value exceeds threshold 2. The process to activate and display this fault
message is described in the "XDIAG" parameter.
The factory setting is "2.0".
G3.LEVL3 - threshold 3
Use this sub-parameter to set a threshold in percent. Use threshold 3 to monitor the upper
hard end stop. Set the threshold in a range from "0.1" to "10.0".
The positioner triggers a fault message if the difference between the upper hard end stop
and the initialization value exceeds threshold 3. The process to activate and display this fault
message is described in the "XDIAG" parameter.
The factory setting is "4.0".
10.4.3.8 Description of parameter H
H.
TMIN - monitoring the lower limit temperature
Use this parameter to activate the test to continuously monitor the lower limit temperature
inside the enclosure. The current temperature in the enclosure is recorded by a sensor on
the electronic printed circuit board. The limit temperature is monitored in three stages.
Configure the following settings to activate the test:
1. Set the "H.
TMIN" parameter to "On". Sub-parameters to set the test parameters are
displayed. The test is activated.
2. Set the suitable parameter values in sub-parameters. The setting options available in
sub-parameters are described below.
The positioner triggers a fault message if the lower limit temperature undershoots a
threshold during the test.
The factory setting is "OFF".
- Electropneumatic positioners 1
- SIPART PS2 with and without 1
- HART communications 1
- Table of contents 3
- Table of contents 5
- Contact person worldwide 10
- See also 10
- Environmental protection 10
- General safety notes 11
- 2.4 Measures 12
- 2.5 Qualified Personnel 13
- 2.6 SIL applications 13
- 2.6 SIL applications 14
- 3.2 Structure 16
- Description 17
- 3.2 Structure 17
- Functional principle 19
- 3.4 Device components 21
- 3.4.2 Motherboard 22
- 3.4.4 Pneumatic connections 23
- Structure 24
- 3.4 Device components 26
- 3.4.5 Purge air switching 27
- 3.4.6 Restrictors 28
- 3.5 Mode of operation 29
- 3.5.2 Control algorithm 30
- 3.5 Mode of operation 31
- Function 32
- Mounting 33
- Installing the positioner 34
- Mounting 35
- 4.5.1 Notes on use 46
- 4.5.2 Friction clutch 48
- Installing option modules 51
- Installing option modules 53
- Installing the module cover 56
- 5.2 Iy module 57
- 5.3 Alarm unit 58
- Installation 59
- 5.4.1 SIA unit 60
- Installing the SIA unit 61
- Setting the L1 and L2 limits 62
- Device features 63
- 5.6 EMC filter module 65
- 5.7 Accessories 67
- Warning labels 68
- Connection 69
- 6.1 Electrical connection 70
- Two-wire mode 71
- 6.1.2.1 Basic device 72
- 6.1.2.2 Current output 73
- 6.1.2.4 SIA unit 74
- Connection 75
- 6.1 Electrical connection 75
- 6.1.3.1 Basic device, Ex i 79
- Basic device 79
- 6.1.3.2 Split range 81
- 6.1.3.5 SIA module, Ex i 84
- 6.1.4.1 Basic device, Ex n 87
- 6.1.4.4 SIA module , Ex n 89
- 6.2 Pneumatic connection 92
- 7.1.2 Buttons 95
- 7.2 Operating modes 96
- VLPXOWDQHRXV VLPXOWDQHRXV 98
- Manual mode (MAN) 99
- Automatic (AUT) 99
- Diagnostics 100
- Operating 101
- Operating 102
- Functional safety 103
- Description 104
- 8.2.2 Safety function 106
- 8.2.3 Settings 107
- Checking the safety function 108
- Repairs 108
- Functional safety 109
- Commissioning 111
- Sequence of RUN1 113
- Commissioning 115
- IODVKHV 117
- DOWHUQDWLQJ 117
- Condition 118
- Connecting the positioner 118
- Setting the actuator 119
- Conditions 120
- Setting parameter 3 121
- Replacing the positioner 131
- Parameterizing/addressing 133
- 10.3 Overview of parameters 135
- Introduction 136
- Overview 136
- Parameterizing/addressing 137
- 10.3 Overview of parameters 138
- Overview parameter A 139
- Overview parameter b 139
- Overview parameter C 140
- Overview parameter d 140
- Overview parameter E 140
- Overview parameter F 140
- Overview parameter G 140
- Overview parameter H 141
- Overview parameter J 141
- Overview parameter L 141
- Overview parameter O 141
- Overview parameter P 142
- 1.YFCT - actuator type 142
- 9.SPRE - Split range end 146
- 10.TSUP - Setpoint ramp OPEN 146
- 12.SFCT - Setpoint function 147
- 44.AFCT - Alarm function 153
- 50.PRST - Preset 156
- PST - partial stroke test 158
- A1.STPOS - start position 158
- A2.STTOL - start tolerance 158
- A3.STEP - step height 159
- A4.STEPD - step direction 159
- A5.INTRV - test interval 159
- A7.FACT1 - factor 1 160
- A8.FACT2 - factor 2 160
- A9.FACT3 - factor 3 160
- DEBA - dead zone monitoring 165
- F1.LEVL1 - threshold 1 166
- F2.LEVL2 - threshold 2 166
- F3.LEVL3 - threshold 3 167
- J1.TUNIT - temperature unit 170
- J2.LEVL1 - threshold 1 170
- J3.LEVL2 - threshold 2 170
- J4.LEVL3 - threshold 3 170
- P3.LEVL1 - threshold 1 174
- P4.LEVL2 - threshold 2 174
- P5.LEVL3 - threshold 3 174
- Messages during operation: 181
- 11.2 Diagnosis 182
- Explanation about the table 183
- Diagnostic value 53 184
- 11.2 Diagnosis 185
- 10 LEAK - leakage 186
- 11.2 Diagnosis 188
- 43 PRUP - prediction up 190
- 44 PRDN - prediction down 190
- 11.3 Online diagnostics 191
- 11.3.2 XDIAG parameter 192
- 11.3 Online diagnostics 194
- 11 Pneumatic leakage 195
- 13 Temperature undershot 196
- 14 Temperature overshot 196
- 11.4 Fault correction 197
- 11.4 Fault correction 202
- Service and maintenance 203
- 12.3 Repair/Upgrading 204
- Technical data 205
- 13.1 General technical data 206
- Technical data 207
- Dimension drawings 215
- Dimension drawings 217
- 15.1 Overview 219
- Accessories 220
- 15.3 Optional modules 222
- 15.4 Spare parts 223
- Small part set 1 224
- Small part set 2 225
- 15.6 Accessories 226
- Appendix 227
- SIEMENS AG, A&D PI TQ2 228
- Management summary 229
- Appendix 231
- A.3 Test report (extract) 231
- A.3 Test report (extract) 232
- Abbreviations 233
- Glossary 235
- Glossary 237
- Zone 22 242
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales