Siemens SIMATIC Distributed I/O System DP/ASi Link Especificaciones Pagina 163
- Pagina / 240
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintenance
7-15
Distributed I/O Device ET 200M
EWA-4NEB780600602-06
Changing Fuses
The fuses are located at the left side of the module.
1. Remove the digital output module as described in Section 7.4
2. Remove the fuse holder from the digital output module.
3. Replace the fuse.
4. Screw the fuse holder back into the digital output module.
5. Install the digital output module again (see Section 7.4).
- Drawing number 1
- Qualified Personnel 2
- Correct Usage 2
- Trademarks 2
- Safety Guidelines 2
- Purpose of the Manual 3
- Required Basic Knowledge 3
- with the 3
- Aids to Finding Information 6
- Recycling and Disposal 6
- Additional Support 6
- Training Center 7
- A&D Technical Support 7
- Contents 9
- EWA-4NEB780600602-06 10
- Product Overview 15
- What Is PROFIBUS-DP? 16
- ”SIMATIC S7-DP Slave” 19
- Features and Functions 22
- Getting Started 27
- 2.1 Introduction 28
- 2.3 Prerequisites 30
- 2.4 Installation 30
- 2.5 Wiring 31
- 2.7 Configuration 34
- 2.9 Switching On 36
- 2.10 Diagnostics 37
- SM 322: Short Circuit to L+ 38
- Operating Principle 43
- Prerequisite 44
- Principle 44
- In the Redundant System 45
- Prerequisites for the ET 200M 47
- Identical Versions 48
- S7-400H as DP master 48
- S5-115H/155H as DP Master 49
- Power Supply of the IM 153-2 49
- 3.7 Clock Synchronism 53
- Time Calculation 58
- Further Information 59
- 3.8 Identification Data 60
- 3.10 Direct Communication 64
- Installation 65
- 4.1 Mechanical Configuration 66
- 4.1.2 Clearance Measurements 67
- Length of the Rails 68
- Installation Options 71
- 4.2 Installation 72
- Fixing Screws 74
- Installing the Rail 75
- Accessories 76
- Sequence for Installation 77
- Modules and Modules) 78
- 4.2.4 After Installation 79
- Applying Slot Numbers 80
- Connecting the Bus Connector 81
- Accessories Required: 82
- Installing Connectors 82
- Reusing Fiber-Optic Cables 83
- Setting the PROFIBUS Address 85
- Changing the PROFIBUS Address 85
- Basic Rules 87
- PNO Installation Guidelines 87
- 5.1 Electrical Configuration 88
- Note on Radio Interference 89
- Mains Voltage 89
- 24V DC Power Supply 89
- Grounded Supply 91
- Rule: Ground Load Circuits 92
- Terminal Connection Model 95
- Power Supply Units 95
- Filtering the 24V DC Supply 96
- Insulation Monitoring 96
- SM 334; AI 4/AO 2 8/8Bit 98
- 5.2 Wiring 99
- Wiring with the Jumper 102
- S7 Explosion-Proof Modules 103
- Types of Front Connector 103
- Spring Terminals 103
- Wiring the Front Connector 105
- Introduction 107
- Application 107
- Attaching Cables 108
- Commissioning and Diagnostics 109
- Software Prerequisites 110
- Commissioning the DP Slave 111
- 6.1.2 Startup of the IM 153-1 112
- 6.1.4 PROFIBUS-DPV1 Mode 116
- 6.2 Diagnostics Using LEDs 118
- The bus communication via 120
- Check that the bus 120
- Slave Diagnostics 121
- Assumptions 122
- STEP 7 User Program 122
- STEP 5 User Program 123
- Notes on Enhanced Diagnosis 125
- With IM 153-2Bx00 125
- 6.4.2 Station Statuses 1 to 3 127
- Station status 2 128
- Station status 3 128
- 6.4.3 Master PROFIBUS Address 129
- 6.4.4 Manufacturer ID 129
- 6.4.5 Module Diagnosis 130
- 6.4.6 Module Status 131
- Definition 132
- Channel-Specific Diagnosis 132
- 6.4.9 Interrupts 137
- Diagnostic Interrupt 138
- Interrupts 139
- Maintenance 149
- 7.2 Replacing the IM 153-1 151
- Installing a New Module 152
- Initial Situation 152
- Slot Numbering 152
- In the Case of Redundancy 154
- Removing a Module 154
- In the Case of Redundancy: 155
- Operation” Function 156
- 7.6 Replacing the Bus Module 161
- Fuses for Digital Outputs 162
- Replacement Fuses 162
- Position of the Fuses 162
- Changing Fuses 163
- 7.8 Update of the IM 153-x 164
- Prerequisites 165
- Sample Configuration 166
- The IM 153-2 automatically 167
- The SF and BF LEDs light up 167
- When the update has been 167
- Restart After Update 168
- Update Not Successful 168
- Technical Specifications 169
- CE Approval 170
- HAZ. LOC 171
- FM Approval 172
- Marking for Australia 172
- IEC 61131 172
- Ship-Building Approval 173
- Use in residential areas 173
- Parameter Assignment 175
- Parameters for Time Stamping 176
- 8.3 Technical Specifications 177
- 8.4 Time Delay of the ET 200M 180
- Weitere Informationen 182
- Fertigungsort 182
- Zulassung 182
- Instandhaltung 183
- Besondere Bedingungen 183
- Hazardous Area 184
- Special Conditions 185
- List of Approved Modules 185
- Informations complémentaires 186
- Lieu de production 186
- Homologation 186
- Entretien 187
- Conditions particulières 187
- Liste des modules homologués 187
- Otras informaciones 188
- Lugar de fabricación 188
- Homologación 188
- Mantenimiento 189
- Condiciones especiales 189
- Ulteriori informazioni 190
- Luogo di produzione 190
- Autorizzazione 190
- Manutenzione 191
- Condizioni particolari 191
- Elenco delle unità abilitate 191
- Productieplaats 192
- Vergunning 192
- Verdere informatie 192
- Instandhouding 193
- Speciale voorwaarden 193
- Yderligere informationer 194
- Produktionssted 194
- Godkendelse 194
- Vedligeholdelse 195
- Særlige betingelser 195
- Vyöhyke 2 196
- Lisätietoja 196
- Valmistuspaikka 196
- Hyväksyntä 196
- Kunnossapito 197
- Erityiset vaatimukset 197
- Ytterligare information 198
- Tillverkningsort 198
- Godkännande 198
- Underhåll 199
- Särskilda villkor 199
- Mais informações 200
- Local de produção 200
- Condições especiais 201
- Επιπλέον πληροφορίες 202
- Τόπος κατασκευής 202
- Συντήρηση 203
- Ιδιαίτερες προϋποθέσεις 203
- In This Chapter 205
- Chapter Overview 205
- IM 153-1 206
- 96-byte diagnostic frame 209
- In the case of redundancy 209
- In the redundant system 209
- In the non-redundant system 209
- Upgrading 210
- Subsequent Versions 212
- Order Numbers for the ET 200M 213
- Glossary 217
- Chassis ground 218
- Clock synchronism 218
- Configuration 218
- Device master file 219
- Diagnostic interrupt 219
- Diagnostics 219
- Distributed I/O devices 219
- DP master 219
- Process interrupt 223
- PROFIBUS 223
- PROFIBUS address 223
- PROFIBUS-DP 224
- Programmable controller 224
- Programming device 224
- Redundant systems 224
- Reference potential 224
- Substitute value 226
- Terminating resistor 226
- Time stamp 226
- Time stamping 227
- Time synchronization 227
- Ungrounded 227
- Glossary-12 228
- Product Information 235
- A5E00272208-01 236
- 1 On Section 1.3 and 9.2 237
- 2 On Section 3.5 237
- A5E00272208-01 238
- 3 On Section 3.7 238
- 5 On Section 6.4.7 240
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales