Siemens SIMATIC NET Manual de servicio Pagina 89
- Pagina / 150
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Command Interface
5-21
SIMATIC NET CP 243-2 AS-i Master
C79000-G8976-C142/02
5.2.9 Get_Extended_Actual_Configuration
Purpose of the Command
With this call, the following configuration data of an addressed AS-i slave obtained
by the AS-i master on the AS-Interface are read.
I/O configuration
ID code
Extended ID1 code
Extended ID2 code
The configuration data are specified by the manufacturer of the AS-i slave. The
meaning of the configuration data is described in /2/.
Structure of the Job Data in the Send Buffer
Bank Byte Meaning
Bit 7 Bit 4 Bit 3 Bit 0
2 0 Command number 28
H
2 1 Slave address
Structure of the Job Data in the Receive Buffer
Bank Byte Meaning
Bit 7 Bit 4 Bit 3 Bit 0
2 0 Echo of the command number: 28
H
2 1 Command status
2 2 ID code I/O configuration
2 3 Extended ID1 code Extended ID2 code
- AS-Interface 1
- Safety Guidelines 2
- Qualified Personnel 2
- Correct Usage 2
- Trademarks 2
- Purpose of the Manual 3
- Requirements 3
- Diskette with Sample Programs 3
- Contents 5
- Instructions 9
- C79000-G8976-C142/02 10
- 1.2 Uses of the Module 11
- Components Supplied 12
- 1.4 Installing the Module 14
- Figure 1-2 15
- 1.6 Terminal Block 16
- 1.7 Modes of the CP 243-2 18
- Meaning of the LEDs 19
- SET Button 19
- 1.8.1 Status Display 20
- 1.8.2 Slave Display 22
- Example of a Slave Display 23
- Configuration Mode 24
- Protected Mode 24
- Preparing to Configure 25
- Configuring 25
- S7-200 CPU 27
- 2.1 Overview 28
- Analog Module 29
- Address Areas 30
- Examples 30
- Status/error information 33
- Control of the CP 33
- Bank selection 33
- Figure 2-2 33
- Range of Values 34
- Meaning for the User Program 35
- Structure of the Status Byte 36
- Description of the Bits 36
- Structure of the Control Byte 37
- Principle 42
- Advantage 42
- Access in the User Program 42
- 2.5.1 Analog Input Area 44
- Banks 16–30: Reserved area 45
- Banks 48–63: Reserved area 46
- 2.5.2 Analog Output Area 47
- Access to the Binary Values 50
- Analog Input Area of the CP) 51
- Analog Output Area of the CP) 51
- input bytes 54
- output bytes16 54
- Data Access with STEP 7 Micro 55
- Access to the Analog Values 56
- Special Situations 62
- User Program 65
- 4.1 Signaling 66
- Table 4-1 67
- Command Sequence 71
- Overview 75
- Command Status 79
- 5.2.1 Set_Permanent_Parameter 81
- 5.2.2 Get_Permanent_Parameter 82
- 5.2.3 Write_Parameter 83
- 5.2.4 Read_Parameter 84
- 5.2.5 Store_Actual_Parameters 85
- Purpose of the Command 88
- 5.2.10 Set_Extended_LPS 90
- 5.2.11 Set_Offline_Mode 91
- 5.2.12 Select_Autoprogramming 92
- 5.2.13 Set_Operation_Mode 93
- 5.2.15 Get_AS-i_Slave_Status 95
- Meaning of the Flags 99
- Command Interface 100
- 5.2.21 Read_Version_ID 115
- 5.2.22 Read_AS-i_Slave_ID 116
- 5.2.23 Read_AS-i_Slave_ID1 117
- 5.2.25 Read_AS-i_Slave_ID2 119
- 5.2.26 Read_AS-i_Slave_I/O 120
- 5.2.27 Get_LPF 121
- Programming 130
- Conformance Statement (PICS) 135
- References 139
- Order numbers 140
- Notes on the CE Mark 141
- SIMATIC Training Center 143
- Further Support 144
- Glossary 145
Relacionado con productos y manuales para No Siemens SIMATIC NET
No Siemens 270 series Manual de usuario
(88 paginas)
(88 paginas)
No Siemens ARTIS 2 Custom Guía de usuario
(45 paginas)
(45 paginas)
No Siemens ePen Manual de usuario
(24 paginas)
(24 paginas)
No Siemens KF Series Manual de instalación
(26 paginas)
(26 paginas)
No Siemens KF91N Series Manual de instalación
(26 paginas)
(26 paginas)
No Siemens SX micon Guía de usuario
(48 paginas)
(48 paginas)
No Siemens Motion Custom Manual de usuario
(20 paginas)
(20 paginas)
No Siemens eCharger Manual de usuario
(84 paginas)
(84 paginas)
No Siemens SINAMICS G150 Especificaciones
(64 paginas)
(64 paginas)
No Siemens Orion SP Manual de usuario
(78 paginas)
(78 paginas)
No Siemens Aquaris micon Guía de usuario
(44 paginas)
(44 paginas)
No Siemens SINAMICS G120 Especificaciones
(76 paginas)
(76 paginas)
No Siemens INTUIS Guía de usuario
(24 paginas)
(24 paginas)
No Siemens ITE Especificaciones
(63 paginas)
(63 paginas)
No Siemens Ric Guía de usuario
(40 paginas)
(40 paginas)
No Siemens D Manual de usuario
(10 paginas)
(10 paginas)
No Siemens Orion SP Especificaciones
(68 paginas)
(68 paginas)
No Siemens KF Series Manual de usuario
(229 paginas)
(229 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.175 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales