Siemens SISTORE AX9 Manual de instalación

6LHPHQV$* Digital Video Recorder SISTORE AX8 1000/200 V4.0 SISTORE AX16 1000/400 V4.0 Installation Manual

Installation 10 Siemens AG EN 05.2010 6 Installation CAUTION Always disconnect the power cable and other cables from the main power supply

Installation 11 Siemens AG EN 05.2010 NOTE z Your DVR can be used with either PAL or NTSC equipment. z You cannot mix PAL and NTSC equipme

Installation 12 Siemens AG EN 05.2010 A VGA connector is provided so that you can use a standard, multi-sync computer monitor as your main monit

Installation 13 Siemens AG EN 05.2010 NOTE All the connectors marked GND are common. Fig. 9 Alarm Output connectors NC/NO (Relay Alarm-

Installation 14 Siemens AG EN 05.2010 6.8 Connecting to the USB ports Fig. 12 USB connectors Two USB ports on the front panel are provided t

Installation 15 Siemens AG EN 05.2010 6.11 Factory reset Fig. 15 Factory reset switch The DVR has a factory reset switch to the left of the V

Installation 16 Siemens AG EN 05.2010 6.13 Connector pin outs I/O connector pin outs AI (1 to 16) Alarm Inputs 1 to 16 GND Chassis Groun

Installation 17 Siemens AG EN 05.2010 6.14 Connection diagrams 6.14.1 Connecting the remote keyboard CKA4820 and dome cameras CCDA1415 and CCDA

Installation 18 Siemens AG EN 05.2010 6.14.2 Local control of CCDA and CCDS dome cameras The following commands are supported when controlling

Installation 19 Siemens AG EN 05.2010 6.14.3 Connecting alarm input/output Recommended Alarm-In connection GNDAlarm InAlarm Device Mechanical a

Liefermöglichkeiten und technische Änderungen vorbehalten. Data and design subject to change without notice. / Supply subject to availability. © 2010

Operation 20 Siemens AG EN 05.2010 7 Operation 7.1 Turning on the power The SISTORE AX8/AX16 is operational in approximately 60 seconds after

Operation 21 Siemens AG EN 05.2010 7.2 Front panel buttons and LEDs Power LED The Power LED is lit when the unit is On. HDD LED The HDD LED fl

Disposal 22 Siemens AG EN 05.2010 7.3 System setup The front panel buttons are used to enter system commands and for programming. Press Menu/Ca

Issued by Siemens AG Siemensallee 84 D-76187 Karlsruhe Tel. +49 721 595 1 www.buildingtechnologies.siemens.com © 2010 Copyright by Siemens AG Data an

3 Siemens AG EN 05.2010 Contents 1 Safety ...

Safety 5 Siemens AG EN 05.2010 1 Safety 1.1 Target readers The instructions in this document are designed for the following target readers: Ta

Safety 6 Siemens AG EN 05.2010 1.2.2 Installation Damage due to unsuitable mounting location z The environmental conditions recommended by the

Directives and standards 7 Siemens AG EN 05.2010 1.3 Meaning of the written warning notices The severity of a hazard is indicated by the follo

Technical data 8 Siemens AG EN 05.2010 3 Technical data Monitoring Video inputs Composite: 8/16 looped through, BNC, PAL/NTSC (auto detect

Details for ordering 9 Siemens AG EN 05.2010 Specifications Power requirements 100 – 240 V AC, 1.2 – 0.6 A, 50/60 Hz ± 10 % Power consumption