Siemens SPCK421 Manual de usuario descargar pdf (Pagina 7)

Page 7 of 11

 SPCE650.100 Expander, 8 input / 2 outputs

The SPCE650.100 Expander extends the SPC system via X-BUS with 8 wired zones and 2 fully

programmable relay outputs. The zones and outputs on the Expander function exactly as the

zones and outputs on the SPC panel.

Each zone can be configured for different zone monitoring requirements. The system supports

4K7 resistors as standard for monitoring as well as support for a range of other resistor values.

The outputs are volt free relays that provide both NO and NC terminals allowing the greatest

flexibility.

The Expander comes in a tamper protected housing (on-board front spring tamper) and features

also an X-BUS status LED and on-board buzzer for easy device identification and extensive self-

diagnostic capabilities.

 SPCE450.100 Expander, 8 relay-outputs

The SPCE450.100 Expander extends the SPC system via X-BUS with 8 fully programmable

relay outputs.

The outputs are volt free relays that provide both NO and NC terminals allowing the greatest

flexibility.

The Expander comes in a tamper protected housing (on-board front spring tamper) and features

also an X-BUS status LED and on-board buzzer for easy device identification and extensive self-

diagnostic capabilities.

 SPCE652.100 Expander, 8 input / 2 outputs, back tamper

The SPCE652.100 Expander extends the SPC system via X-BUS with 8 wired zones and 2 fully

programmable relay outputs. The zones and outputs on the expander function exactly as the

zones and outputs on the SPC panel. Each zone can be configured for different zone monitoring

requirements. The system supports 4K7 resistors as standard for monitoring as well as support

for a range of other resistor values. The outputs are volt free relays that provide both NO and NC

terminals allowing the greatest flexibility. The expander comes in a tamper protected housing

(on-board front / back spring tampers) and features also an X-BUS status LED and on board

buzzer for easy device identification and extensive self-diagnostic capabilities.

 SPCE452 Expander, 8 relay-outputs, back tamper

The SPCE452.100 Expander extends the SPC system via X-BUS with 8 fully programmable

relay outputs. The outputs are volt free relays that provide both NO and NC terminals allowing

the greatest flexibility. The relay can be activated under a number of conditions. The Expander

comes in a tamper protected housing (on-board front / back spring tampers) and features also

an X-BUS status LED and on board buzzer for easy device identification and extensive self-

diagnostic capabilities.



SPCA210.100 2-Door expander

The SPCA210.100 2-Door Expander extends the SPC6000 with advanced door control

functionality for 2 entry doors or 1 entry/exit door.

The device features 2 Wiegand/Clock&Data interfaces, 4 LED control outputs (1 void / 1 valid

per reader), 4 zones (1 position- and 1 opening switch per door), 2 relay outputs (1 lock per

door) and an on-board buzzer to signal "door open too long" events. The zones and outputs

function exactly as for the SPC panel.

To allow greatest flexibility, the zones and outputs are freely programmable for other purposes if

not used for door control. Up to 512 priority card holders can be stored on the expander for

standalone operation in case of communication loss to the control panel.

The Expander comes in a tamper protected housing (on-board front spring tamper) and features

also an X-BUS status LED for easy device identification and extensive self-diagnostic

capabilities.

1 2 3 4 5 6 7 8 9 10 11

Comentarios a estos manuales

Sin comentarios

Siemens SPCK421 Manual de usuario Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Teclados numéricos Siemens SPCK421